- 您現在的位置：買賣IC網 > PDF目錄369480 > BQ2083 Silicon Bridge Rectifiers PDF資料下載
參數資料
| 型號： | BQ2083 |
| 英文描述： | Silicon Bridge Rectifiers |
| 中文描述： | 銀紫荊星章符合電量監測計芯片的使用與BQ29311 |
| 文件頁數： | 19/54頁 |
| 文件大小： | 461K |
| 代理商： | BQ2083 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
SLUS573 JULY 2003
www.ti.com
19
When Miscellaneous Configuration (0x2a) bit 5 AC is set, and the AFE has failed at least AFE Fail Times (DF
0xd3, d4)
The bq2083V1P2 checks the programming of the AFE registers at a period determined by AFE Check Time DF
0xe4. The units of the check period are seconds unless the bq2083V1P2 is in sleep mode, in which case the period
is
AFE
Check Time
x
Sleep Current Time
(DF 0xe7). If the data is not correct, the bq2083V1P2 increments an
internal counter.
The CVOV flag in PackStatus() (0x2f) is set in any of the following ways:
Voltage()
≥
ChargingVoltage() + OverVoltageMargin (DF 0x5a and 0x5b)
AverageCurrent()
≥
FastCurrent + OvercurrentMargin (DF 0x5c and 0x5d)
Any cell voltage
≥
CellOverVoltage (DF 0x60 and 0x61)
The BatteryStatus() Over temperature bit is set
An example circuit using the SAFE output to blow a fuse is shown in Figure 5.
SAFE
VCC
100 k
1 M
1 M
BSS84
2N7002
BAT+
FUSE
Cell 4
0.1
μ
F
Figure 5. Example SAFE Circuit Implementation
Low-Power Modes
The bq2083V1P2 enters sleep mode when the charge and discharge current is less than the threshold programmed
in
Sleep Current Threshold
DF 0xe5, the SMBus lines are low for at least 2 s, and bit 4 of
Misc. Configuration
DF
0x2a is set to zero. The bq2083V1P2 wakes up periodically to monitor voltage and temperature and to apply
self-discharge adjustment. The sleep period is set in
Sleep Timer
DF 0xe7. The bq2083V1P2 wakes up at a period
set by
Sleep Current Time
DF 0xe6 to measure current. The bq2083V1P2 comes out of sleep when the SMBus
lines go high or if the current is greater than
Sleep Current Threshold
. A rising edge on SMBC or SMBD restores the
bq2083V1P2 to the full operating mode.
Reset Conditions
On power-up the entire IC is reset and data is loaded from Data Flash to configure the SBS Data and the system.
On a partial reset (loss of VCC but RBI holds RAM valid) then a limited number of actions are taken.
These actions are the following:
The AFE registers are rewritten.
PackStatus() VDQ flag is cleared (the proposed change is not to clear VDQ).
PackStatus() EDV2 flag is cleared.
BatteryStatus() DISCHARGING flag is cleared.
The charger and alarm broadcast period is set to 10 seconds between broadcasts.
相關PDF資料 |
PDF描述 |
|---|---|
| BQ2201PN-N | Fast Recovery Bridge Rectifiers |
| BQ2201S-N | Fast Recovery Bridge Rectifiers |
| BQ2201SN(NARROW) | Fast Recovery Bridge Rectifiers |
| BQ2201SN-N | Fast Recovery Bridge Rectifiers |
| BQ2212PN | Fast Recovery Bridge Rectifiers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BQ20832DBT | 制造商:Texas Instruments 功能描述: |
| BQ20832DBTR | 制造商:Texas Instruments 功能描述: |
| BQ2083DBT | 功能描述:電池管理 SBS-Cmplnt Gas Gauge for Use w/BQ29311 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| BQ2083DBTG4 | 功能描述:電池管理 SBS-Cmplnt Gas Gauge for Use w/BQ29311 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| BQ2083DBTR | 功能描述:電池管理 SBS-Cmplnt Gas Gauge for Use w/BQ29311 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。