參數資料
型號: AM79C978
廠商: Advanced Micro Devices, Inc.
英文描述: Single-Chip 1/10 Mbps PCI Home Networking Controller
中文描述: 單芯片的1 / 10 Mbps的家庭網絡控制器的PCI
文件頁數: 28/261頁
文件大小: 3803K
代理商: AM79C978
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁第243頁第244頁第245頁第246頁第247頁第248頁第249頁第250頁第251頁第252頁第253頁第254頁第255頁第256頁第257頁第258頁第259頁第260頁第261頁
28
Am79C978
When RST is active, REQ is an input for NAND tree
testing
.
RST
Reset
When RST is asserted LOW and the PG pin is HIGH,
then the Am79C978 controller performs an internal
system
reset
of
the
(HARDWARE_RESET, see section on RESET). RST
must be held for a minimum of 30 clock periods. While
in the H_RESET state, the Am79C978 controller will
disable or deassert all outputs. RST may be asynchro-
nous to clock when asserted or deasserted.
Input
type
H_RESET
When the PG pin is LOW, RST disables all of the PCI
pins except the PME pin.
When RST is LOW and PG is HIGH, NAND tree testing
is enabled.
SERR
System Error
During any slave transaction, the Am79C978 controller
asserts SERR when it detects an address parity error,
and reporting of the error is enabled by setting PER-
REN (PCI Command register, bit 6) and SERREN (PCI
Command register, bit 8) to 1.
Output
By default SERR is an open-drain output. For compo-
nent test, it can be programmed to be an active-high
totem-pole output.
When RST is active, SERR is an input for NAND tree
testing
.
STOP
Stop
In slave mode, the Am79C978 controller drives the
STOP signal to inform the bus master to stop the cur-
rent transaction. In bus master mode, the Am79C978
controller checks STOP to determine if the target wants
to disconnect the current transaction.
Input/Output
When RST is active, STOP is an input for NAND tree
testing
.
TRDY
Target Ready
TRDY indicates the ability of the target of the transac-
tion to complete the current data phase. Wait states are
inserted until both IRDY and TRDY are asserted simul-
taneously. A data phase is completed on any clock
when both IRDY and TRDY are asserted.
Input/Output
When the Am79C978 controller is a bus master, it
checks TRDY during all read data phases to determine
if valid data is present on AD[31:0]. During all write data
phases, the device checks TRDY to determine if the
target is ready to accept the data.
When the Am79C978 controller is the target of a trans-
action, it asserts TRDY during all read data phases to
indicate that valid data is present on AD[31:0]. During
all write data phases, the device asserts TRDY to indi-
cate that it is ready to accept the data.
When RST is active, TRDY is an input for NAND tree
testing
.
Magic Packet Interface
PME
Power Management Event Output, Open Drain
PME is an output that can be used to indicate that a
power management event (a Magic Packet, an OnNow
pattern match, or a change in link state) has been de-
tected. The PME pin is asserted when either
1. PME_STATUS and PME_EN are both 1,
2. PME_EN_OVR and MPMAT are both 1, or
3. PME_EN_OVR and LCDET are both 1.
The PME signal is asynchronous with respect to the
PCI clock. See the
Power Saving Mode
section for de-
tailed description.
PG
Power Good
The PG pin has two functions: (1) it puts the device into
Magic Packet mode, and (2) it blocks any resets when
the PCI bus power is off.
Input
When PG is LOW and either MPPEN or MPMODE is
set to 1, the device enters Magic Packet mode.
When PG is LOW, a LOW assertion of the PCI RST pin
will only cause the PCI interface pins (except for PME)
to be put in the high impedance state. The internal logic
will ignore the assertion of RST.
When PG is HIGH, assertion of the PCI RST pin
causes the controller logic to be reset and the configu-
ration information to be loaded from the EEPROM.
Note:
PG input should be kept high during NAND tree
testing.
Board Interface
Note:
Before programming the LED pins, see the
description of LEDPE in BCR2, bit 12.
LED0
LED0
This output is designed to directly drive an LED. By de-
fault, LED0 indicates an active link connection. This pin
can also be programmed to indicate other network sta-
tus (see BCR4). The LED0 pin polarity is programma-
ble, but by default it is active LOW. When the LED0 pin
polarity is programmed to active LOW, the output is an
open drain driver. When the LED0 pin polarity is pro-
Output
相關PDF資料
PDF描述
AM79C981 Integrated Multiport Repeater Plus⑩ (IMR+⑩)
AM79C981JC Integrated Multiport Repeater Plus⑩ (IMR+⑩)
AM79C982 basic Integrated Multiport Repeater (bIMR)
AM79C982-4JC basic Integrated Multiport Repeater (bIMR)
AM79C982-8JC basic Integrated Multiport Repeater (bIMR)
相關代理商/技術參數
參數描述
AM79C978A 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Single-Chip 1/10 Mbps PCI Home Networking Controller
AM79C978AKC\\W 制造商:Advanced Micro Devices 功能描述:
AM79C978AKC\W 制造商:Advanced Micro Devices 功能描述:
AM79C978AKCW 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Single-Chip 1/10 Mbps PCI Home Networking Controller