- 您現在的位置：買賣IC網 > PDF目錄10968 > ADV7173KSTZ-REEL (Analog Devices Inc)IC DAC VIDEO NTSC 6-CH 48LQFP PDF資料下載
參數資料
| 型號： | ADV7173KSTZ-REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 18/60頁 |
| 文件大小： | 0K |
| 描述： | IC DAC VIDEO NTSC 6-CH 48LQFP |
| 標準包裝： | 2,000 |
| 類型： | 視頻編碼器 |
| 應用： | 多媒體 |
| 電壓 - 電源，模擬： | 4.75 V ~ 5.25 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP（7x7） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
REV. B
ADV7172/ADV7173
–25–
The ADV7172/ADV7173 acts as a standard slave device on the
bus. The data on the SDATA pin is eight bits long, supporting
the 7-bit addresses plus the R/
W bit. It interprets the first byte
as the device address and the second byte as the starting sub-
address. The subaddresses auto increment allows data to be
written to or read from the starting subaddress. A data transfer
is always terminated by a stop condition. The user can also
access any unique subaddress register on a one-by-one basis
without having to update all the registers. There is one excep-
tion. The subcarrier frequency registers should be updated in
sequence, starting with Subcarrier Frequency Register 0. The
auto increment function should then be used to increment and
access Subcarrier Frequency Registers 1, 2 and 3. The subcarrier
frequency registers should not be accessed independently.
Stop and Start conditions can be detected at any stage during
the data transfer. If these conditions are asserted out of sequence
with normal read and write operations, then these cause an
immediate jump to the idle condition. During a given SCLOCK
high period, the user should issue only one start condition, one
stop condition or a single stop condition followed by a single start
condition. If an invalid subaddress is issued by the user, the
ADV7172/ADV7173 will not issue an acknowledge and will
return to the idle condition. If, in autoincrement mode, the user
exceeds the highest subaddress, the following action will be taken:
1. In Read Mode the highest subaddress register contents
will continue to be output until the master device issues
a no-acknowledge. This indicates the end of a read. A
no-acknowledge condition is where the SDATA line is not
pulled low on the ninth pulse.
2. In Write Mode, the data for the invalid byte will not be loaded
into any subaddress register, a no-acknowledge will be issued
by the ADV7172/ADV7173 and the part will return to the
idle condition.
Figure 41 illustrates an example of data transfer for a read
sequence and the Start and Stop conditions.
1-7
8
9
1-7
8
9
1-7
8
9
P
S
START ADDR R/W ACK SUBADDRESS ACK
DATA
ACK
STOP
SDATA
SCLOCK
Figure 41. Bus Data Transfer
Figure 42 shows bus write and read sequences.
REGISTER ACCESSES
The MPU can write to or read from all of the registers of the
ADV7172/ADV7173 except the Subaddress Register, which is a
write-only register. The Subaddress Register determines which
register the next read or write operation accesses. All communi-
cations with the part through the bus start with an access to the
Subaddress Register. A read/write operation is then performed
from/to the target address, which then increments to the next
address until a Stop command on the bus is performed.
REGISTER PROGRAMMING
The following section describes each register, including subaddress
register, mode registers, subcarrier frequency registers, subcar-
rier phase register, timing registers, closed captioning extended
data registers, closed captioning data registers, NTSC pedestal
Control/PAL teletext control registers, CGMS/WSS registers,
contrast register, U- or V-scale registers, hue adjust register,
brightness control register and sharpness control register in
terms of its configuration. All registers can be read from as well
as written to.
DATA
A(S)
S
SLAVE ADDR A(S)
SUB ADDR
A(S)
LSB = 0
LSB = 1
DATA
A(S) P
S
SLAVE ADDR
A(S)
SUB ADDR
A(S) S SLAVE ADDR
A(S)
DATA
A(M)
DATA
P
WRITE
SEQUENCE
READ
SEQUENCE
A(S) = NO-ACKNOWLEDGE BY SLAVE
A(M) = NO-ACKNOWLEDGE BY MASTER
A(S) = ACKNOWLEDGE BY SLAVE
A(M) = ACKNOWLEDGE BY MASTER
S = START BIT
P = STOP BIT
A(M)
Figure 42. Write and Read Sequences
相關PDF資料 |
PDF描述 |
|---|---|
| S9S12XS256J0VAE | MCU 16BIT 256K FLASH 64LQFP |
| ADV7393BCPZ-REEL | IC DAC ENCODER VID HDTV 40-LFCSP |
| MC9S12GC32MFAE | IC MCU 32K FLASH 25MHZ 48-LQFP |
| ADV7171KSUZ-REEL | IC DAC VIDEO ENC NTSC 44TQFP TR |
| CS4954-CQZR | IC VID ENCODER NTSC/PAL 48-TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADV7174 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Chip Scale PAL/NTSC Video Encoder with Advanced Power Management |
| ADV7174BCP | 制造商:AD 制造商全稱:Analog Devices 功能描述:Chip Scale PAL/NTSC Video Encoder with Advanced Power Management |
| ADV7174BCP-REEL | 制造商:AD 制造商全稱:Analog Devices 功能描述:Chip Scale PAL/NTSC Video Encoder with Advanced Power Management |
| ADV7174KCP | 制造商:AD 制造商全稱:Analog Devices 功能描述:Chip Scale PAL/NTSC Video Encoder with Advanced Power Management |
| ADV7174KCP-REEL | 制造商:AD 制造商全稱:Analog Devices 功能描述:Chip Scale PAL/NTSC Video Encoder with Advanced Power Management |
發(fā)布緊急采購，3分鐘左右您將得到回復。