參數資料
型號: ADUC832BCP
廠商: ANALOG DEVICES INC
元件分類: 微控制器/微處理器
英文描述: MicroConverter, 12-Bit ADCs and DACs with Embedded 62 kBytes Flash MCU
中文描述: 8-BIT, FLASH, 16.78 MHz, MICROCONTROLLER, PQFP52
封裝: MO-112AC-1, MQFP-52
文件頁數: 66/80頁
文件大?。?/td> 1311K
代理商: ADUC832BCP
REV. 0
–66–
ADuC832
Windows is a registered trademark of Microsoft Corporation.
Embedded Serial Port Debugger
From a hardware perspective, entry into serial port debug mode
is identical to the serial download entry sequence described
above. In fact, both serial download and serial port debug modes
can be thought of as essentially one mode of operation used in
two different ways.
Note that the serial port debugger is fully contained on the
ADuC832 device, (unlike ROM monitor type debuggers) and
therefore no external memory is needed to enable in-system
debug sessions.
Single-Pin Emulation Mode
Also built into the ADuC832 is a dedicated controller for
single-pin in-circuit emulation (ICE) using standard production
ADuC832 devices. In this mode, emulation access is gained by
connection to a single pin, the
EA
pin. Normally, this pin is
hardwired either high or low to select execution from internal or
external program memory space, as described earlier. To enable
single-pin emulation mode, however, users will need to pull the
EA
pin high through a 1 k
resistor as shown in Figure 64.
The emulator will then connect to the 2-pin header also shown
in Figure 64. To be compatible with the standard connector
that comes with the single-pin emulator available from Accutron
Limited (www.accutron.com), use a 2-pin 0.1 inch pitch
Friction
Lock
header from Molex (www.molex.com) such as their part
number 22-27-2021. Be sure to observe the polarity of this
header. As represented in Figure 64, when the Friction Lock tab
is at the right, the ground pin should be the lower of the two
pins (when viewed from the top).
Typical System Configuration
A typical ADuC832 configuration is shown in Figure 64. It
summarizes some of the hardware considerations discussed in
the previous paragraphs.
DEVELOPMENT TOOLS
There are two models of development tools available for the
ADuC832, namely:
QuickStart
Entry-level development system
QuickStart Plus
Comprehensive development system
These systems are described briefly below.
QuickStart Development System
The QuickStart Development System is an entry-level, low cost
development tool suite supporting the ADuC832. The system
consists of the following PC-based (Windows
compatible)
hardware and software development tools.
Hardware:
ADuC832 Evaluation Board and
Serial Port Programming Cable.
Software:
ASPIRE Integrated Development
Environment. Incorporates 8051
assembler and serial port debugger.
Serial Download Software.
Miscellaneous:
CD-ROM Documentation and
Prototype Device.
Figure 65 shows the typical components of a QuickStart Develop-
ment System. A brief description of some of the software tools
components in the QuickStart Development System follows.
Figure 65. Components of the QuickStart
Development System
Figure 66. Typical Debug Session
Download—In-Circuit Serial Downloader
The Serial Downloader is a Windows application that allows the
user to serially download an assembled program (Intel Hex format
file) to the on-chip program FLASH memory via the serial
COM1 port on a standard PC. An Application Note (uC004)
detailing this serial download protocol is available from
www.analog.com/microconverter.
ASPIRE—IDE
The ASPIRE Integrated Development Environment is a Windows
application that allows the user to compile, edit, and debug code
in the same environment. The ASPIRE software allows users to
debug code execution on silicon using the MicroConverter UART
serial port. The debugger provides access to all on-chip peripherals
during a typical debug session as well as single-step, animate,
and break-point code execution control.
Note, the ASPIRE IDE is also included as part of the QuickStart
Plus System. As part of the QuickStart Plus System, the ASPIRE
IDE also supports mixed level and C source debug. This is not
available in the QuickStart System, but there is an example
project that demonstrates this capability.
相關PDF資料
PDF描述
ADUC832BS MicroConverter, 12-Bit ADCs and DACs with Embedded 62 kBytes Flash MCU
ADUC834 MicroConverter, Dual 16-/24- Bit ADCs with Embedded 62KB FLASH MCU
ADUC834BS MicroConverter, Dual 16-/24- Bit ADCs with Embedded 62KB FLASH MCU
ADUM1310BRWZ Triple-Channel Digital Isolator with Programmable Default Output
ADUM1310BRWZ-RL Triple-Channel Digital Isolator with Programmable Default Output
相關代理商/技術參數
參數描述
ADUC832BCP-REEL 制造商:Analog Devices 功能描述:MCU 8-Bit ADuC8xx 8052 CISC 62KB Flash 3V/5V 56-Pin LFCSP EP T/R
ADUC832BCPZ 功能描述:IC MCU 62K FLASH ADC/DAC 56LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:MicroConverter® ADuC8xx 標準包裝:250 系列:LPC11Uxx 核心處理器:ARM? Cortex?-M0 芯體尺寸:32-位 速度:50MHz 連通性:I²C,Microwire,SPI,SSI,SSP,UART/USART,USB 外圍設備:欠壓檢測/復位,POR,WDT 輸入/輸出數:40 程序存儲器容量:96KB(96K x 8) 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 3.6 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-LQFP 包裝:托盤 其它名稱:568-9587
ADUC832BCPZ-REEL 功能描述:IC MCU 62K FLASH ADC/DAC 56LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:MicroConverter® ADuC8xx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA,UART/USART 外圍設備:欠壓檢測/復位,LED,POR,PWM,WDT 輸入/輸出數:16 程序存儲器容量:4KB(4K x 8) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC(0.295",7.50mm 寬) 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC832BS 制造商:Analog Devices 功能描述:MCU 8-Bit ADuC8xx 8052 CISC 62KB Flash 3.3V/5V 52-Pin MQFP 制造商:Rochester Electronics LLC 功能描述:8BIT CISC 62KB FLASH 16.78MHZ 3.3/5V 52MQFP - Bulk 制造商:Analog Devices 功能描述:8BIT MCU +12BIT ADC LQFP52 832
ADUC832BS-REEL 制造商:Analog Devices 功能描述:MCU 8-Bit ADuC8xx 8052 CISC 62KB Flash 3.3V/5V 52-Pin MQFP T/R