- 您現在的位置：買賣IC網 > PDF目錄11204 > ADUC7036DCPZ-RL (Analog Devices Inc)IC MCU 96K FLASH DUAL 48LFCSP PDF資料下載
參數資料
| 型號： | ADUC7036DCPZ-RL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 84/132頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU 96K FLASH DUAL 48LFCSP |
| 標準包裝： | 2,500 |
| 系列： | MicroConverter® ADuC7xxx |
| 核心處理器： | ARM7 |
| 芯體尺寸： | 16/32-位 |
| 速度： | 20.48MHz |
| 連通性： | LIN，SPI，UART/USART |
| 外圍設備： | PSM，溫度傳感器，WDT |
| 輸入/輸出數： | 9 |
| 程序存儲器容量： | 96KB（48K x 16） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 1.5K x 32 |
| 電壓 - 電源 (Vcc/Vdd)： | 3.5 V ~ 18 V |
| 數據轉換器： | A/D 2x16b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 115°C |
| 封裝/外殼： | 48-VFQFN 裸露焊盤，CSP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁當前第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁
ADuC7036
Rev. C | Page 55 of 132
Current Channel ADC Accumulator Register
Name: ADC0ACC
Address: 0xFFFF055C
Default Value: 0x00000000
Access: Read only
Function: This 32-bit MMR holds the current accumulator
value. The I-ADC ready bit in the ADCSTA MMR should be
used to determine when it is safe to read this MMR. The MMR
value is reset to 0 by disabling the accumulator in the ADCCFG
MMR or reconfiguring the current channel ADC.
Low Power Voltage Reference Scaling Factor Register
Name: ADCREF
Address: 0xFFFF057C
Default Value: Part specific, factory programmed
Access: Read/write. Care should be taken not to write to this
register.
Function: This MMR allows user code to correct for the initial
error of the LPM reference. Value 0x8000 corresponds to no
error when compared to the normal mode reference. The magni-
tude of the ADC result should be multiplied by the value in
ADCREF and divided by 0x8000 to compensate for the actual
value of the low power reference. If the LPM voltage reference
is 1% below 1.2 V, the value of ADCREF is approximately
0x7EB9. If the LPM voltage reference is 1% above 1.2 V, the
value of ADCREF is approximately 0x8147.
This register corrects the effective value of the LPM reference at
the temperature at which the reference is measured during the
Analog Devices, Inc., production flow, which is 25°C. There is
no change to the temperature coefficient of the LPM reference
when using the ADCREF MMR.
This register should not be used if the precision reference is
being used in low power mode (if ADCMDE[5] is set).
ADC POWER MODES OF OPERATION
The ADCs can be configured into various reduced or full
power modes of operation by changing the configuration of
ADCMDE[4:3], and the ARM7 MCU can be configured in low
power modes of operation (POWCON[5:3]). The core power
modes are independently controlled and are not related to the
ADC power modes described in the following sections.
ADC Normal Power Mode
In normal mode, the current and voltage/temperature channels
are fully enabled. The ADC modulator clock is 512 kHz and
enables the ADCs to provide regular conversion results at a rate
between 4 Hz and 8 kHz (see the ADC Filter Register section).
Both channels are under full control of the MCU and can be
reconfigured at any time. The default ADC update rate for all
channels in this mode is 1 kHz.
Note that the I-ADC and V-/T-ADC channels can be
configured to initiate periodic single conversion cycles in
normal power mode with high accuracy before returning to
ADC full power-down mode. This flexibility is facilitated by
full MCU control via the ADCMDE MMR, which ensures the
feasibility of continuous periodic monitoring of battery current,
voltage, and temperature settings while minimizing the average
dc current consumption.
In ADC normal mode, the PLL must not be powered down.
ADC Low Power Mode
In ADC low power mode, the I-ADC is enabled in a reduced
power and reduced accuracy configuration. The ADC modu-
lator clock is driven directly from the on-chip 131 kHz low
power oscillator, which allows the ADC to be configured at
update rates as low as 1 Hz (ADCFLT). The gain of the ADC
in this mode is fixed at 128.
All ADC peripheral functions (result counter, digital comparator
and accumulator) described in the ADC Normal Power Mode
section can also be enabled in low power mode.
Typically, in low power mode, only the I-ADC is configured to
run at a low update rate, continuously monitoring battery current.
The MCU is in power-down mode and wakes up when the I-ADC
interrupts the MCU. Such an interrupt occurs after the I-ADC
detects a current conversion beyond a preprogrammed threshold,
a setpoint, or a set number of conversions.
It is also possible to select either the ADC precision voltage
reference or the ADC low power mode voltage reference via
ADCMDE[5].
ADC Low Power Plus Mode
In low power plus mode, the I-ADC channel is enabled in a
mode almost identical to low power mode (ADCMDE[4:3]).
However, in this mode, the I-ADC gain is fixed at 512, and the
ADC consumes an additional 200 μA (approximately) to yield
improved noise performance relative to the low power mode
setting.
All ADC peripheral functions (result counter, digital comparator,
and accumulator) described in the ADC Normal Power Mode
section can also be enabled in low power plus mode.
As in low power mode, only the I-ADC is configured to run at
a low update rate, continuously monitoring battery current. The
MCU is in power-down mode and wakes up only when the I-ADC
interrupts the MCU. This happens after the I-ADC detects a
current conversion result that exceeds a preprogrammed
threshold or a setpoint.
It is also possible to select either the ADC precision voltage
reference or the ADC low power mode voltage reference via
ADCMDE[5].
相關PDF資料 |
PDF描述 |
|---|---|
| ADUC7036BCPZ-RL | IC SENSOR AUTO 96K FLASH 48LFCSP |
| ADUC7019BCPZ62IRL7 | IC MCU 12BIT 1MSPS I2C 40-LFCSP |
| AT91M42800A-33AU-999 | IC MCU 32BIT RISC 144LQFP |
| ADUC7027BSTZ62-RL | IC MCU 12BIT 1MSPS UART 80-LQFP |
| MB91F267APMC-GE1 | IC MCU FLASH 128KB FLASH 64LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADUC7038WBCPZ-RL | 制造商:Analog Devices 功能描述:FLASH 64K ARM7 DUAL 16-BIT ADC 制造商:Analog Devices 功能描述:FLASH 64K ARM7 DUAL 16-BIT ADC LIN I.C. - Tape and Reel 制造商:Analog Devices 功能描述:IC MCU ARM7 制造商:Analog Devices 功能描述:ARM Microcontrollers - MCU Flash 64k ARM7 Dual 16-Bit ADC LIN IC 制造商:Analog Devices 功能描述:Flash 64k ARM7 Dual 16-Bit ADC LIN I.C. |
| ADUC7039 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Integrated, Precision Battery Sensor for Automotive Systems |
| ADUC7039BCP6Z | 功能描述:IC MCU ARM7 BATT SENSER 32LFCSP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:250 系列:LPC11Uxx 核心處理器:ARM? Cortex?-M0 芯體尺寸:32-位 速度:50MHz 連通性:I²C，Microwire，SPI，SSI，SSP，UART/USART，USB 外圍設備:欠壓檢測/復位，POR，WDT 輸入/輸出數:40 程序存儲器容量:96KB（96K x 8） 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 3.6 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-LQFP 包裝:托盤 其它名稱:568-9587 |
| ADUC7039BCP6Z-RL | 功能描述:IC MCU ARM7 BATT SENSER 32LFCSP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND |
| ADUC7039WBCPZ | 制造商:Analog Devices 功能描述:FLASH 64K ARM7 DUAL 16-BIT ADC LIN I.C. - Trays 制造商:Analog Devices 功能描述:IC MCU ARM7 64KB FLASH 32LFCSP 制造商:Analog Devices 功能描述:Flash 64k ARM7 Dual 16-Bit ADC LIN I.C. |
發布緊急采購，3分鐘左右您將得到回復。