參數資料
型號： ADUC7036DCPZ-RL
廠商： Analog Devices Inc
文件頁數： 14/132頁
文件大?。?/td> 0K
描述： IC MCU 96K FLASH DUAL 48LFCSP
標準包裝： 2,500
系列： MicroConverter® ADuC7xxx
核心處理器： ARM7
芯體尺寸： 16/32-位
速度： 20.48MHz
連通性： LIN，SPI，UART/USART
外圍設備： PSM，溫度傳感器，WDT
輸入/輸出數： 9
程序存儲器容量： 96KB（48K x 16）
程序存儲器類型： 閃存
RAM 容量： 1.5K x 32
電壓 - 電源 (Vcc/Vdd)： 3.5 V ~ 18 V
數據轉換器： A/D 2x16b
振蕩器型： 內部
工作溫度： -40°C ~ 115°C
封裝/外殼： 48-VFQFN 裸露焊盤，CSP
包裝： 帶卷 (TR)
ADuC7036
Rev. C | Page 110 of 132
SERIAL PERIPHERAL INTERFACE
In master mode, polarity and phase of the clock is controlled by
the SPICON register, and the bit rate is defined in the SPIDIV
register using the SPI baud rate calculation, as follows:
The ADuC7036 features a complete hardware serial peripheral
interface (SPI) on chip. SPI is an industry-standard synchronous
serial interface that allows eight bits of data to be synchronously
transmitted and received simultaneously, that is, full duplex.
)
1
(
2
MHz
48
.
20
SPIDIV
f
CLOCK
SERIAL
+
×
=
(3)
The SPI interface is operational only with core clock divider bits
(POWCON[2:0] = 0000 or 001).
The maximum speed of the SPI clock is dependent on the clock
divider bits and is summarized in Table 88.
The SPI port can be configured for master or slave operation
and consists of four pins that are multiplexed with four GPIOs.
The four SPI pins are MISO, MOSI, SCLK, and SS. The pins to
which these signals are connected are shown in
.
Table 88. SPI Speed vs. Clock Divider Bits in Master Mode
Setting of CD Bits
SPIDIV
Maximum SCLK (MHz)
0
0x05
1.667
Table 87. SPI Output Pins
Pin
SPI
Pin Function
1
0x0B
0.833
Description
In slave mode, the SPICON register must be configured with
the phase and polarity of the expected input clock. The slave
accepts data of up to 5.12 Mb from an external master when
CD = 0. The formula to determine the maximum speed is as
follows:
GP0 (GPIO Mode 1)
SS
Chip select
GP1 (GPIO Mode 1)
SCLK
Serial clock
GP2 (GPIO Mode 1)
MISO
Master input, slave output
GP3 (GPIO Mode 1)
MOSI
Master output, slave input
4
HCLK
CLOCK
SERIAL
f
=
(4)
MISO PIN
The MISO (master input, slave output) pin is configured as an
input line in master mode and as an output line in slave mode.
The MISO line on the master (data in) should be connected to
the MISO line in the slave device (data out). The data is transferred
as byte-wide (8-bit) serial data, MSB first.
In both master and slave modes, data is transmitted on one edge
of the SCL signal and sampled on the other. Therefore, it is
important to use the same polarity and phase configurations for
the master and slave devices.
SS PIN
MOSI PIN
The MOSI (master output, slave input) pin is configured as an
output line in master mode and as an input line in slave mode.
The MOSI line on the master (data out) should be connected to
the MOSI line in the slave device (data in). The data is transferred
as byte-wide (8-bit) serial data, MSB first.
In SPI slave mode, a transfer is initiated by the assertion of SS,
an active low input signal. The SPI port transmits and receives
eight bits of data, and then the transfer is concluded by the
deassertion of SS. In slave mode, SS is always an input.
SPI REGISTER DEFINITIONS
SCLK PIN
The following MMR registers are used to control the SPI
interface:
The SCLK (master serial clock) pin is used to synchronize the
data being transmitted and received through the MOSI SCLK
period. Therefore, a byte is transmitted/received after eight
SCLK periods. The SCLK pin is configured as an output in
master mode and as an input in slave mode.
SPICON: 16-bit control register
SPISTA: 8-bit, read only status register
SPIDIV: 8-bit, serial clock divider register
SPITX: 8-bit, write only transmit register
SPIRX: 8-bit, read only receive register
相關PDF資料
PDF描述
ADUC7036BCPZ-RL IC SENSOR AUTO 96K FLASH 48LFCSP
ADUC7019BCPZ62IRL7 IC MCU 12BIT 1MSPS I2C 40-LFCSP
AT91M42800A-33AU-999 IC MCU 32BIT RISC 144LQFP
ADUC7027BSTZ62-RL IC MCU 12BIT 1MSPS UART 80-LQFP
MB91F267APMC-GE1 IC MCU FLASH 128KB FLASH 64LQFP
相關代理商/技術參數
參數描述
ADUC7038WBCPZ-RL 制造商:Analog Devices 功能描述:FLASH 64K ARM7 DUAL 16-BIT ADC 制造商:Analog Devices 功能描述:FLASH 64K ARM7 DUAL 16-BIT ADC LIN I.C. - Tape and Reel 制造商:Analog Devices 功能描述:IC MCU ARM7 制造商:Analog Devices 功能描述:ARM Microcontrollers - MCU Flash 64k ARM7 Dual 16-Bit ADC LIN IC 制造商:Analog Devices 功能描述:Flash 64k ARM7 Dual 16-Bit ADC LIN I.C.
ADUC7039 制造商:AD 制造商全稱:Analog Devices 功能描述:Integrated, Precision Battery Sensor for Automotive Systems
ADUC7039BCP6Z 功能描述:IC MCU ARM7 BATT SENSER 32LFCSP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:250 系列:LPC11Uxx 核心處理器:ARM? Cortex?-M0 芯體尺寸:32-位 速度:50MHz 連通性:I²C，Microwire，SPI，SSI，SSP，UART/USART，USB 外圍設備:欠壓檢測/復位，POR，WDT 輸入/輸出數:40 程序存儲器容量:96KB（96K x 8） 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 3.6 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-LQFP 包裝:托盤 其它名稱:568-9587
ADUC7039BCP6Z-RL 功能描述:IC MCU ARM7 BATT SENSER 32LFCSP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC7039WBCPZ 制造商:Analog Devices 功能描述:FLASH 64K ARM7 DUAL 16-BIT ADC LIN I.C. - Trays 制造商:Analog Devices 功能描述:IC MCU ARM7 64KB FLASH 32LFCSP 制造商:Analog Devices 功能描述:Flash 64k ARM7 Dual 16-Bit ADC LIN I.C.
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*