參數資料
型號： ADSP-2192M
廠商： Analog Devices, Inc.
元件分類： 數字信號處理
英文描述： DSP Microcomputer
中文描述： DSP微機
文件頁數： 8/40頁
文件大?。?/td> 1307K
代理商： ADSP-2192M
ADSP-2192M
–8–
REV. 0
space uses a single DSP clock cycle to perform the internal DSP
data transfer. Byte-wide accesses to DSP memory are not
supported.
I/O type accesses are supported via BAR4. Both the control
registers accessible via BAR1 and the DSP memory accessible
via BAR2 and BAR3 can be accessed with I/O accesses. Indirect
access is used to read and write both the control registers and the
DSP memory. For the control register accesses, an address reg-
ister points to the word to be accessed while a separate register is
used to transfer the data. Read/write control is part of the address
register. Only 16-bit accesses are possible via the I/O space.
A separate set of registers is used to perform the same function
for DSP memory access. Control for these accesses includes a
24-bit/16-bit select as well as direction control. The data register
for DSP memory accesses is a full 24 bits wide. 16-bit accesses
will be loaded into the lower 16 bits of the register.
Table 10 on
Page 14
lists the registers directly accessible from BAR4.
Bus Master Interface
As a bus master, the PCI interface can transfer DMA data
between system memory and the DSP. The control registers for
these transfers are available both to the host and to the DSPs.
Four channels of bus mastering DMA are supported on the
ADSP-2192M.
Two channels are associated with the receive data and two are
associated with the transmit data. The internal DSPs will
typically control initiation of bus master transactions. DMA host
bus master transfers can specify either standard circular buffers
in system memory or perform scatter-gather DMA to host
memory.
Each bus master DMA channel includes four registers to specify
a standard circular buffer in system memory. The Base Address
points to the start of the circular buffer. The Current Address is
a pointer to the current position within that buffer. The Base
Count specifies the size of the buffer in bytes, while the Current
Count keeps track of how many bytes need to be transferred
before the end of the buffer is reached. When the end of the buffer
is reached, the channel can be programmed to loop back to the
beginning and continue the transfers. When this looping occurs,
a Status bit will be set in the DMA Control Register.
The PCI DMA controller can be programmed to perform
scatter-gather DMA, when transferring samples to and from DSP
memory. This mode allows the data to be split up in memory,
and yet be transferable to and from the ADSP-2192M without
processor intervention. In scatter-gather mode, the DMA con-
troller can read the memory address and word count from an
array of buffer descriptors called the Scatter-Gather Descriptor
(SGD) table. This allows the DMA engine to sustain DMA
transfers until all buffers in the SGD table are transferred.
To initiate a scatter-gather transfer between memory and the
ADSP-2192M, the following steps are involved:
1. Software driver prepares a SGD table in system memory.
Each descriptor is eight bytes long and consists of an
address pointer to the starting address and the transfer
count of the memory buffer to be transferred. In any
given SGD table, two consecutive SGDs are offset by
eight bytes and are aligned on a 4-byte boundary. Each
SGD contains:
a.Memory Address (Buffer Start) – 4 bytes
b.Byte Count (Buffer Size) – 3 bytes
c.End of Linked List (EOL) – 1 bit (MSBit)
d.Flag – 1 bit (MSBit – 1)
2. Initialize DMA control registers with transfer-specific
information such as number of total bytes to transfer,
direction of transfer, etc.
3. Software driver initializes the hardware pointer to the
SGD table.
4. Engage scatter-gather DMA by writing the start value to
the PCI channel Control/Status register.
5. The ADSP-2192M will then pull in samples as pointed
to by the descriptors as needed by the DMA engine.
When the EOL is reached, a status bit will be set and the
DMA will end if the data buffer is not to be looped. If
looping is to occur, DMA transfers will continue from
the beginning of the table until the channel is turned off.
6. Bits in the PCI Control/Status register control whether
an interrupt occurs when the EOL is reached or when
the FLAG bit is set.
Scatter-gather DMA uses four registers. In scatter-gather mode
the functions of the registers are mapped as shown in
Table 4
.
In either mode of operation, interrupts can be generated based
upon the total number of bytes transferred. Each channel has two
24-bit registers to count the bytes transferred and generate inter-
rupts as appropriate. The Interrupt Base Count register specifies
the number of bytes to transfer prior to generating an interrupt.
The Interrupt Count register specifies the current number left
prior to generating the interrupt. When the Interrupt Count
Table 4. Register Mapping in Scatter-Gather Mode
Standard Circular
Buffer Mode
Scatter-Gather Mode
Function
Base Address
Current Address
SGD Table Pointer
SGD Current Pointer
Address
SGD Pointer
Current SGD Count
Base Count
Current Count
相關PDF資料
PDF描述
ADSP-21992 Mixed Signal DSP Controller With CAN
ADSP-21992YST Mixed Signal DSP Controller With CAN
ADSP-21MOD970-510 Multiport Internet Gateway Processor Data Pump Solution(多端口網關處理器數據泵解決方案)
ADSP-21mod970 Multi-Port Internet Gateway Processor(多口網關處理器)
ADSP-21msp58 DSP Microcomputer(DSP 微計算機)
相關代理商/技術參數
參數描述
ADSP-2195MBCA-140 制造商:Analog Devices 功能描述:DSP Fixed-Point 24-Bit 140MHz 140MIPS 144-Pin CSP-BGA 制造商:Rochester Electronics LLC 功能描述:16-BIT,140 MIPS, 2.5V, 80KBYTES RAM - Bulk
ADSP-2195MBST-140 功能描述:IC DSP CONTROLLER 16BIT 144LQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:ADSP-21xx 標準包裝:40 系列:TMS320DM64x, DaVinci™ 類型:定點 接口:I²C，McASP，McBSP 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:160kB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:0°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:548-BBGA，F(xiàn)CBGA 供應商設備封裝:548-FCBGA（27x27） 包裝:托盤 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA
ADSP-2195MKCA-160 制造商:Analog Devices 功能描述:DSP Fixed-Point 24-Bit 160MHz 160MIPS 144-Pin CSP-BGA 制造商:Rochester Electronics LLC 功能描述:16-BIT,160 MIPS, 2.5V, 80KBYTES RAM - Bulk
ADSP-2195MKST-160 制造商:Analog Devices 功能描述:DSP Fixed-Point 24-Bit 160MHz 160MIPS 144-Pin LQFP 制造商:Analog Devices 功能描述:IC MICROCOMPUTER 16-BIT
adsp-2196mbca-140 制造商:Analog Devices 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*