參數資料
型號： AD9991KCPZRL
廠商： Analog Devices Inc
文件頁數： 20/60頁
文件大?。?/td> 0K
描述： IC CCD SIGNAL PROCESSOR 56-LFCSP
產品變化通告： Product Discontinuance 27/Oct/2011
標準包裝： 2,500
類型： CCD 信號處理器，10 位
輸入類型： 邏輯
輸出類型： 邏輯
接口： 3 線串口
安裝類型： 表面貼裝
封裝/外殼： 56-VFQFN 裸露焊盤，CSP
供應商設備封裝： 56-LFCSP-VQ（8x8）
包裝： 帶卷 (TR)
AD9991
–27–
If the exposure is generated using the TRIGGER register and the
EXPOSURE register is set to zero, the behavior of the SUBCK
will not be any different than the normal shutter or high precision
shutter operations, in which the TRIGGER register is not used.
SUBCK Suppression
Normally, the SUBCKs will begin to pulse on the line following
the sensor gate line (VSG). With some CCDs, the SUBCK pulse
needs to be suppressed for one or more lines following the VSG
line. The SUBCKSUPPRESS register allows for suppression of
the SUBCK pulses for additional lines following the VSG line.
Readout after Exposure
After the exposure, the readout of the CCD data occurs, beginning
with the sensor gate (VSG) operation. By default, the AD9991 is
generating the VSG pulses in every eld. In the case where only a
single exposure and single readout frame are needed, such as the
CCD’s preview mode, the VSG and SUBCK pulses can be oper-
ating in every eld.
However in many cases, during readout the SUBCK output
needs to be further suppressed until the readout is completed.
The READOUT register species the number of additional
elds after the exposure to continue the suppression of SUBCK.
READOUT can be programmed for zero to seven additional
elds, and should be preprogrammed at startup, not at the same
time as the exposure write. A typical interlaced CCD frame read-
out mode will generally require two additional elds of SUBCK
suppression (READOUT = 2). A 3-eld, 6-phase CCD will
require three additional elds of SUBCK suppression after the
readout begins (READOUT = 3).
If the SUBCK output is required to start back up during the last
eld of readout, simply program the READOUT register to one
less than the total number of CCD readout elds.
Like the exposure operation, the readout operation must be trig-
gered by using the TRIGGER register.
Using the TRIGGER Register
As described previously, by default the AD9991 will output the
SUBCK and VSG signals on every eld. This works well for con-
tinuous single eld exposure and readout operations, such as the
CCD’s live preview mode. However, if the CCD requires a longer
exposure time, or if multiple readout elds are needed, then the
TRIGGER register is needed to initiate specic exposure and
readout sequences.
Typically, the exposure and readout bits in the TRIGGER
register are used together. This will initiate a complete exposure-
plus-readout operation. Once the exposure has been completed,
the readout will automatically occur. The values in the EXPO-
SURE and READOUT registers will determine the length of
each operation.
VD
SUBCK
NOTES
1. SUBCK MAY BE SUPPRESSED FOR MULTIPLE FIELDS BY PROGRAMMING THE EXPOSURE REGISTER GREATER THAN ZERO.
2. ABOVE EXAMPLE USES EXPOSURE = 1.
3. TRIGGER REGISTER MUST ALSO BE USED TO START THE LOW SPEED EXPOSURE.
4. VD/HD OUTPUTS MAY ALSO BE SUPPRESSED USING THE VDHDOFF REGISTER = 1.
t
EXP
VSG
TRIGGER
EXPOSURE
Figure 28. Low Speed Shutter Mode Using EXPOSURE Register
Table XI. Shutter Mode Register Parameters
Register
Length
Range
Description
TRIGGER
5b
On/Off for Five Signals
Trigger for VSUB [0], MSHUT [1], STROBE [2], Exposure [3],
and Readout Start [4]
READOUT
3b
0–7 # of Fields
Number of Fields to Suppress SUBCK after Exposure
EXPOSURE
12b
0–4095 # of Fields
Number of Fields to Suppress to SUBCK and VSG during
Exposure Time (Low Speed Shutter)
VDHDOFF
1b
On/Off
Disable VD/HD Output during Exposure (1 = On, 0 = Off)
SUBCKPOL
*
1b
High/Low
SUBCK Start Polarity for SUBCK1 and SUBCK2
SUBCK1TOG
*
24b
0–4095 Pixel Locations
Toggle Positions for First SUBCK Pulse (Normal Shutter)
SUBCK2TOG
*
24b
0–4095 Pixel Locations
Toggle Positions for Second SUBCK Pulse in Last Line
(High Precision)
SUBCKNUM
*
12b
1–4095 # of Pulses
Total Number of SUBCKs per Field, at One Pulse per Line
SUBCKSUPPRESS
*
12b
0–4095 # of Pulses
Number of Lines to Further Suppress SUBCK after the VSG Line
*Register is not VD updated, but is updated at the start of line after sensor gate line.
REV. 0
相關PDF資料
PDF描述
AD9992BBCZRL IC CCD SGNL PROC 12BIT 105CSPBGA
AD9995KCPZ IC CCD SIGNAL PROCESSOR 56-LFCSP
ADA4424-6ARUZ IC FILTR VID6CH SD/ED/HD 38TSSOP
ADATE302-02BBCZ IC DCL ATE 500MHZ DUAL 84CSPBGA
ADATE304BBCZ IC DCL ATE 200MHZ DUAL 84CSPBGA
相關代理商/技術參數
參數描述
AD9992 制造商:AD 制造商全稱:Analog Devices 功能描述:12-Bit CCD Signal Processor with Precision Timing Generator
AD9992_07 制造商:AD 制造商全稱:Analog Devices 功能描述:12-Bit CCD Signal Processor with Precision Timing Generator
AD9992BBCZ 功能描述:IC CCD SGNL PROC 12BIT 105CSPBGA RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件
AD9992BBCZRL 功能描述:IC CCD SGNL PROC 12BIT 105CSPBGA RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件
AD9993BBCZ 功能描述:IC MIXED-SIGNAL FRONT END 196BGA 制造商:analog devices inc. 系列:- 包裝:托盤 零件狀態:在售 類型:ADC，DAC 輸入類型:LVDS 輸出類型:LVDS 接口:SPI 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:196-LFBGA，CSPBGA 供應商器件封裝:196-CSPBGA（12x12） 標準包裝:1
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*