- 您現在的位置：買賣IC網 > PDF目錄10978 > AD9958BCPZ (Analog Devices Inc)IC DDS DUAL 500MSPS DAC 56LFCSP PDF資料下載
參數資料
| 型號： | AD9958BCPZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 33/44頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DDS DUAL 500MSPS DAC 56LFCSP |
| 產品培訓模塊： | Direct Digital Synthesis Tutorial Series (1 of 7): Introduction Direct Digital Synthesizer Tutorial Series (7 of 7): DDS in Action Direct Digital Synthesis Tutorial Series (3 of 7): Angle to Amplitude Converter Direct Digital Synthesis Tutorial Series (6 of 7): SINC Envelope Correction Direct Digital Synthesis Tutorial Series (4 of 7): Digital-to-Analog Converter Direct Digital Synthesis Tutorial Series (2 of 7): The Accumulator |
| 設計資源： | Low Jitter Sampling Clock Generator for High Performance ADCs Using AD9958/9858 and AD9515 (CN0109) Phase Coherent FSK Modulator (CN0186) |
| 標準包裝： | 1 |
| 分辨率（位）： | 10 b |
| 主 fclk： | 500MHz |
| 調節字寬（位）： | 32 b |
| 電源電壓： | 1.71 V ~ 1.96 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 56-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 56-LFCSP-VQ（8x8） |
| 包裝： | 托盤 |
| 產品目錄頁面： | 552 (CN2011-ZH PDF) |
| 配用： | AD9958/PCBZ-ND - BOARD EVALUATION FOR AD9958 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
Data Sheet
AD9958
Rev. B | Page 39 of 44
DESCRIPTIONS FOR CONTROL REGISTERS
Channel Select Register (CSR)—Address 0x00
One byte is assigned to this register.
The CSR determines if channels are enabled or disabled by the status of the two channel enable bits. Both channels are enabled by their
default state. The CSR also determines which serial mode of operation is selected. In addition, the CSR offers a choice of MSB first or LSB
first format.
Table 31. Bit Descriptions for CSR
Bit
Mnemonic
Description
7:6
Channel [1:0] enable
Bits are active immediately after being written. They do not require an I/O update to take effect.
There are two sets of channel registers and profile (channel word) registers, one per channel. This
is not shown in the channel register map or the profile register map. The addresses of all channel
registers and profile registers are the same for each channel. Therefore, the channel enable bits
distinguish the channel registers and profile registers values of each channel. For example,
10 = only Channel 1 receives commands from the channel registers and profile registers.
01 = only Channel 0 receives commands from the channel registers and profile registers.
11 = both Channel 0 and Channel 1 receive commands from the channel registers and profile
registers.
5:4
Open
3
Must be 0
Must be set to 0.
2:1
Serial I/O mode select
00 = single-bit serial (2-wire mode).
01 = single-bit serial (3-wire mode).
10 = 2-bit serial mode.
11 = 4-bit serial mode.
See the Serial I/O Modes of Operation section for more details.
0
LSB first
0 = the serial interface accepts serial data in MSB first format (default).
1 = the serial interface accepts serial data in LSB first format.
Function Register 1 (FR1)—Address 0x01
Three bytes are assigned to this register. FR1 is used to control the mode of operation of the chip.
Table 32. Bit Descriptions for FR1
Bit
Mnemonic
Description
23
VCO gain control
0 = the low range (system clock below 160 MHz) (default).
1 = the high range (system clock above 255 MHz).
22:18
PLL divider ratio
If the value is 4 or 20 (decimal) or between 4 and 20, the PLL is enabled and the value sets the
multiplication factor. If the value is outside of 4 and 20 (decimal), the PLL is disabled.
17:16
Charge pump control
00 (default) = the charge pump current is 75 A.
01 = charge pump current is 100 A.
10 = charge pump current is 125 A.
11 = charge pump current is 150 A.
15
Open
14:12
Profile pin configuration (PPC)
The profile pin configuration bits control the configuration of the data and SDIO_x pins for the
different modulation modes. See the Modulation Mode section in this document for details.
11:10
Ramp-up/ramp-down (RU/RD)
The RU/RD bits control the amplitude ramp-up/ramp-down time of a channel. See the Output
Amplitude Control Mode section for more details.
9:8
Modulation level
The modulation (FSK, PSK, and ASK) level bits control the level (2/4/8/16) of modulation to be
performed for a channel. See the Modulation Mode section for more details.
7
Reference clock input
0 = the clock input circuitry is enabled for operation (default).
power-down
1 = the clock input circuitry is disabled and is in a low power dissipation state.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B1D-IY-F1 | CONVERTER MOD DC/DC 85V 50W |
| VE-B1B-IY-F3 | CONVERTER MOD DC/DC 95V 50W |
| VE-B13-IY-F2 | CONVERTER MOD DC/DC 24V 50W |
| VE-B12-IY-F3 | CONVERTER MOD DC/DC 15V 50W |
| AD9954YSVZ | IC DDS DAC 14BIT 1.8V 48-TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9958BCPZ-REEL7 | 功能描述:IC DDS DUAL 10BIT DAC 56LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 直接數字合成 (DDS) 系列:- 產品變化通告:Product Discontinuance 27/Oct/2011 標準包裝:2,500 系列:- 分辨率（位）:10 b 主 fclk:25MHz 調節字寬（位）:32 b 電源電壓:2.97 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| AD9959 | 制造商:AD 制造商全稱:Analog Devices 功能描述:4 Channel 500MSPS DDS with 10-bit DACs |
| AD9959/PCBZ | 功能描述:BOARD EVALUATION FOR AD9959 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PSoC® 主要目的:電源管理，熱管理 嵌入式:- 已用 IC / 零件:- 主要屬性:- 次要屬性:- 已供物品:板，CD，電源 |
| AD9959/PCBZ | 制造商:Analog Devices 功能描述:AD9959, DDS, DAC, GUI, USB, EVALUATION B |
| AD9959/PCBZ1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:4-Channel, 500 MSPS DDS with 10-Bit DACs |
發布緊急采購，3分鐘左右您將得到回復。