參數資料
型號： AD9548BCPZ-REEL7
廠商： Analog Devices Inc
文件頁數： 5/112頁
文件大?。?/td> 0K
描述： IC CLOCK GEN/SYNCHRONIZR 88LFCSP
產品變化通告： AD9548 Mask Change 20/Oct/2010
標準包裝： 400
類型： 時鐘/頻率發生器，同步器
PLL： 是
主要目的： 以太網，SONET/SDH，Stratum
輸入： CMOS，LVDS，LVPECL
輸出： CMOS，LVDS，LVPECL
電路數： 1
比率 - 輸入:輸出： 1:1
差分 - 輸入:輸出： 是/是
頻率 - 最大： 750kHz
電源電壓： 1.71 V ~ 3.465 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 88-VFQFN 裸露焊盤，CSP
供應商設備封裝： 88-LFCSP-VQ（12x12）
包裝： 帶卷 (TR)
AD9548
Data Sheet
Rev. E | Page 102 of 112
NONVOLATILE MEMORY (EEPROM) CONTROL (REGISTER 0x0E00 TO REGISTER 0x0E03)
Table 142. EEPROM Control
Address
Bits
Bit Name
Description
0x0E00
[7:2]
Unused
[1]
Half rate mode
EEPROM serial communication rate.
0 (default) = 400 kHz (normal).
1 = 200 kHz.
[0]
Write enable
EEPROM write enable/protect.
0 (default) = EEPROM write protected.
1 = EEPROM write enabled.
0x0E01
[7:5]
Unused
[4:0]
Condition value
When set to a nonzero value (default = 0), these bits establish the condition for
EEPROM downloads.
0x0E02
[7:1]
Unused
[0]
Save to EEPROM
Upload data to the EEPROM based on the EEPROM storage sequence. This is an
autoclearing bit. When an EEPROM save/load transfer is complete, wait a minimum of
10 μs before starting the next EEPROM save/load transfer.
0x0E03
[7:2]
Unused
[1]
Load from EEPROM
Download data from the EEPROM. This is an autoclearing bit. When an EEPROM
save/load transfer is complete, wait a minimum of 10 μs before starting the next
EEPROM save/load transfer.
[0]
Unused
EEPROM STORAGE SEQUENCE (REGISTER 0x0E10 TO REGISTER 0x0E3F)
The default settings of Register 0x0E10 to Register 0x0E33 embody a sample scratch pad instruction sequence. The following is a
description of the register defaults under the assumption that the controller has been instructed to carry out an EEPROM storage
sequence.
Table 143. EEPROM Storage Sequence for System Clock Settings
Address
Bits
Bit Name
Description
0x0E10
[7:0]
System clock
The default value of this register is 0x08, which the controller interprets as a data
instruction. Its decimal value is 8, which tells the controller to transfer nine bytes of
data (8 + 1) beginning at the address specified by the next two bytes. The
controller stores 0x08 in the EEPROM and increments the EEPROM address pointer.
0x0E11
[7:0]
System clock
The default value of these two registers is 0x0100. Note that Register 0x0E11 and
Register 0x0E12 are the most significant and least significant bytes of the target
address, respectively. Because the previous register contains a data instruction,
these two registers define a starting address (in this case, 0x0100). The controller
stores 0x0100 in the EEPROM and increments the EEPROM pointer by 2. It then
transfers nine bytes from the register map (beginning at Address 0x0100) to the
EEPROM and increments the EEPROM address pointer by 10 (nine data bytes and
one checksum byte). The nine bytes transferred correspond to the system clock
parameters in the register map.
0x0E12
[7:0]
0x0E13
[7:0]
I/O update
The default value of this register is 0x80, which the controller interprets as an I/O
update instruction. The controller stores 0x80 in the EEPROM and increments the
EEPROM address pointer.
Table 144. EEPROM Storage Sequence for System Clock Calibration
Address
Bits
Bit Name
Description
0x0E14
[7:0]
SYSCLK calibrate
The default value of this register is 0xA0, which the controller interprets as a
calibrate instruction. The controller stores 0xA0 in the EEPROM and increments the
EEPROM address pointer.
相關PDF資料
PDF描述
AD9549ABCPZ-REEL7 IC CLOCK GEN/SYNCHRONIZR 64LFCSP
AD9550BCPZ-REEL7 IC INTEGER-N TRANSLATOR 32-LFCSP
AD9551BCPZ IC CLOCK GEN MULTISERV 40-LFCSP
AD9552BCPZ-REEL7 IC PLL CLOCK GEN LP 32LFCSP
AD9553BCPZ-REEL7 IC INTEGER-N CLCK GEN 32LFCSP
相關代理商/技術參數
參數描述
AD9548XCPZ 制造商:Analog Devices 功能描述:
AD9549 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual Input Network Clock Generator/Synchronizer
AD9549/PCBZ 制造商:Analog Devices 功能描述:DUAL INPUT NETWORK CLOCK GEN/SYNCHRONIZER - Bulk
AD9549A/PCBZ 功能描述:BOARD EVALUATION FOR AD9549A RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PSoC® 主要目的:電源管理，熱管理 嵌入式:- 已用 IC / 零件:- 主要屬性:- 次要屬性:- 已供物品:板，CD，電源
AD9549ABCPZ 功能描述:IC CLOCK GEN/SYNCHRONIZR 64LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:1 系列:- 類型:時鐘/頻率發生器，多路復用器 PLL:是 主要目的:存儲器，RDRAM 輸入:晶體 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:1:2 差分 - 輸入:輸出:無/是 頻率 - 最大:400MHz 電源電壓:3 V ~ 3.6 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:Digi-Reel® 其它名稱:296-6719-6
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*