參數資料
| 型號： | AD9148BBCZRL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 63/72頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC 16BIT QD 1GSPS 196CSPBGA |
| 標準包裝： | 1,500 |
| 系列： | TxDAC+® |
| 設置時間： | 20ns |
| 位數： | 16 |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 4 |
| 電壓電源： | 模擬和數字 |
| 功率耗散（最大）： | 2.22W |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 196-LFBGA，CSPBGA |
| 供應商設備封裝： | 196-CSPBGA（12x12） |
| 包裝： | 帶卷 (TR) |
| 輸出數目和類型： | 8 電流，單極 |
| 采樣率（每秒）： | 1G |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁當前第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
AD9148
Data Sheet
Rev. B | Page 66 of 72
INTERRUPT REQUEST OPERATION
The AD9148 provides an interrupt request output signal
(Pin H4, IRQ) that can be used to notify an external host
processor of significant device events. Upon assertion of the
interrupt, the device should be queried to determine the precise
event that occurred. The IRQ pin is an open-drain, active low
output.
Pull the IRQ pin high external to the device. This pin may be
tied to the interrupt pins of other devices with open-drain outputs
to wired-OR these pins together.
Ten different event flags provide visibility into the device. These
10 flags are located in the two event flag registers (Register 0x06
and Register 0x07). The behavior of each of the event flags is
independently selected in the interrupt enable registers
(Register 0x04 and Register 0x05). When the flag interrupt
enable is active, the event flag latches and triggers an external
interrupt. When the flag interrupt is disabled, the event flag
simply monitors the source signal, and the external IRQ
remains inactive.
Figure 91 shows the IRQ-related circuitry. Figure 91 shows how the
event flag signals propagate to the IRQ output. The interupt_enable
signal represents one bit from the interrupt enable register. The
event_flag signal represents one bit from the event flag register.
The event_flag_source signal represents one of the device signals
that can be monitored such as the PLL_locked signal from the
PLL phase detector or the FIFO Warning 1 signal from the
FIFO controller.
When an interrupt enable bit is set high, the corresponding event
flag bit reflects a positively tripped (that is, latched on the rising
edge of the event_flag_source version of the event_flag_source signal.
This signal also asserts the external IRQ. When an interrupt enable
bit is set low, the event flag bit reflects the current status of the
event_flag_source signal, and the event flag has no effect on the
external IRQ.
The latched version of an event flag (the interupt_source signal)
can be cleared in two ways. The recommended way is by writing 1
to the corresponding event flag bit. A hardware or software reset
also clears the interupt_source.
INTERRUPT SERVICE ROUTINE
Interrupt request management starts by selecting the set of event
flags that require host intervention or monitoring. Those events
that require host action should be enabled so that the host is
notified when they occur. For events requiring host intervention,
upon IRQ activation, run the following routine to clear an
interrupt request:
Read the status of the event flag bits that are being
monitored.
Set the interupt enable bit low so that the unlatched
event_flag_source can be monitored directly.
Perform any actions that may be required to quiet the
event_source_flag. In many cases, no specific actions may
be required.
Read the event flag to verify that the actions taken have
quieted the event_flag_source.
Clear the interrupt by writing 1 to the event flag bit.
Set the interrupt enable bits of the events to be monitored.
Noted that some of the event_flag_source signals are latched
signals. These are cleared by writing to the corresponding event
flag bit. Details of each of the event flags can be found in Table 12.
INTERRUPT_ENABLE
EVENT_FLAG_SOURCE
DEVICE_RESET
EVENT_FLAG
INTERRUPT
SOURCE
1
0
OTHER
INTERRUPT
SOURCES
IRQ
WRITE_1_TO_EVENT_FLAG
08910-
088
Figure 91. Simplified Schematic of IRQ Circuitry
相關PDF資料 |
PDF描述 |
|---|---|
| VE-JTK-MW-S | CONVERTER MOD DC/DC 40V 100W |
| AD5372BSTZ-REEL | IC DAC 16BIT 32CH SER 64-LQFP |
| VE-JTJ-MW-S | CONVERTER MOD DC/DC 36V 100W |
| VE-JTH-MW-S | CONVERTER MOD DC/DC 52V 100W |
| AD5382BSTZ-5 | IC DAC 14BIT 32CH 5V 100-LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9148BBPZ | 功能描述:IC DAC 16BIT SPI/SRL 196BGA RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TxDAC+® 標準包裝:1 系列:- 設置時間:4.5µs 位數:12 數據接口:串行，SPI? 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOICN 包裝:剪切帶 (CT) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:* 其它名稱:MCP4921T-E/SNCTMCP4921T-E/SNRCTMCP4921T-E/SNRCT-ND |
| AD9148BBPZRL | 功能描述:IC DAC 16BIT SPI/SRL 196BGA RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TxDAC+® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 設置時間:1µs 位數:8 數據接口:串行 轉換器數目:8 電壓電源:雙 ± 功率耗散（最大）:941mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC W 包裝:帶卷 (TR) 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
| AD9148BPCZ | 制造商:AD 制造商全稱:Analog Devices 功能描述:Quad 16-Bit,1 GSPS, TxDAC+ Digital-to-Analog Converter |
| AD9148BPCZRL | 制造商:AD 制造商全稱:Analog Devices 功能描述:Quad 16-Bit,1 GSPS, TxDAC+ Digital-to-Analog Converter |
| AD9148-EBZ | 功能描述:BOARD EVALUATION FOR AD9148 RoHS:是 類別:編程器，開發(fā)系統(tǒng) >> 評估板 - 數模轉換器 (DAC) 系列:TxDAC+® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
發(fā)布緊急采購，3分鐘左右您將得到回復。