- 您現在的位置：買賣IC網 > PDF目錄8554 > AD9148BBCZRL (Analog Devices Inc)IC DAC 16BIT QD 1GSPS 196CSPBGA PDF資料下載
參數資料
| 型號： | AD9148BBCZRL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 40/72頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC 16BIT QD 1GSPS 196CSPBGA |
| 標準包裝： | 1,500 |
| 系列： | TxDAC+® |
| 設置時間： | 20ns |
| 位數： | 16 |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 4 |
| 電壓電源： | 模擬和數字 |
| 功率耗散（最大）： | 2.22W |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 196-LFBGA，CSPBGA |
| 供應商設備封裝： | 196-CSPBGA（12x12） |
| 包裝： | 帶卷 (TR) |
| 輸出數目和類型： | 8 電流，單極 |
| 采樣率（每秒）： | 1G |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
Data Sheet
AD9148
Rev. B | Page 45 of 72
DEVICE SYNCHRONIZATION
SYNCHRONIZING MULTIPLE DEVICES
System demands may require that the outputs of multiple DACs
be synchronized with each other or with a system clock. Systems
that support transmit diversity or beam-forming, where multiple
antennas are used to transmit a correlated signal, require multiple
DAC outputs to be phase aligned with each other. Systems with
a time-division multiplexing transmit chain may require one or
more DACs to be synchronized with a system-level reference clock.
Multiple devices are considered synchronized to each other when
the state of the clock generation state machines is identical for all
parts and time aligned data is being read from the FIFOs of all
parts simultaneously. Devices are considered synchronized to a
system clock when there is a fixed and known relationship between
the clock generation state machine and the data being read from
the FIFO and a particular clock edge of the system clock. The
AD9148 has provisions for enabling multiple devices to be
synchronized to each other or to a system clock.
The AD9148 supports synchronization in two different modes,
data rate mode and FIFO rate mode. The two modes are
distinguished by the lowest rate clock that the synchronization
logic attempts to synchronize. In data rate mode, the input data
rate represents the lowest synchronized clock. In FIFO rate mode,
the FIFO rate, which is the data rate divided by the FIFO depth
of 8, represents the lowest rate clock. The advantage of the FIFO
rate synchronization is increased setup and hold times of DCI
relative to the CLK input. When in data rate synchronization
mode, the elasticity of the FIFO is not used to absorb timing
variations between the data source and DAC, resulting in
tighter setup and hold time requirements.
The method chosen for providing the DAC sampling clock directly
impacts the synchronization methods available. When the device
clock multiplier is used, only data rate synchronization is
available. When the DAC sampling clock is sourced directly,
both data rate mode and FIFO rate mode synchronization are
available.
SYNCHRONIZATION WITH CLOCK MULTIPLICATION
When using the clock multiplier to generate the DACCLK, the
REFCLK/SYNC input signal acts as both the reference clock for
the PLL-based clock multiplier and as the synchronization signal.
To synchronize devices, the REFCLK/SYNC signal must be
distributed with low skew to all of the devices to be synchronized.
Skew between the REFCLK/SYNC signals of different devices show
up directly as a timing mismatch at the DAC outputs.
The frequency of the REFCLK/SYNC signal is typically equal to
the input data rate. The FRAME signal and DCI signals can be
created in the FPGA along with the data. A circuit diagram of a
typical configuration is shown in Figure 53.
SYSTEM CLOCK
FPGA
LOW SKEW
CLOCK DRIVER
MATCHED
LENGTH TRACES
MATCHED
LENGTH TRACES
REFCLK/SYNC
FRAME
DCI
REFCLK/SYNC
FRAME
DCI
OUT1
OUT2
08910-
052
Figure 53. Typical Circuit Diagram for Synchronizing Devices with Clock Multiplication Enabled
相關PDF資料 |
PDF描述 |
|---|---|
| VE-JTK-MW-S | CONVERTER MOD DC/DC 40V 100W |
| AD5372BSTZ-REEL | IC DAC 16BIT 32CH SER 64-LQFP |
| VE-JTJ-MW-S | CONVERTER MOD DC/DC 36V 100W |
| VE-JTH-MW-S | CONVERTER MOD DC/DC 52V 100W |
| AD5382BSTZ-5 | IC DAC 14BIT 32CH 5V 100-LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9148BBPZ | 功能描述:IC DAC 16BIT SPI/SRL 196BGA RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TxDAC+® 標準包裝:1 系列:- 設置時間:4.5µs 位數:12 數據接口:串行，SPI? 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOICN 包裝:剪切帶 (CT) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:* 其它名稱:MCP4921T-E/SNCTMCP4921T-E/SNRCTMCP4921T-E/SNRCT-ND |
| AD9148BBPZRL | 功能描述:IC DAC 16BIT SPI/SRL 196BGA RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TxDAC+® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 設置時間:1µs 位數:8 數據接口:串行 轉換器數目:8 電壓電源:雙 ± 功率耗散（最大）:941mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC W 包裝:帶卷 (TR) 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
| AD9148BPCZ | 制造商:AD 制造商全稱:Analog Devices 功能描述:Quad 16-Bit,1 GSPS, TxDAC+ Digital-to-Analog Converter |
| AD9148BPCZRL | 制造商:AD 制造商全稱:Analog Devices 功能描述:Quad 16-Bit,1 GSPS, TxDAC+ Digital-to-Analog Converter |
| AD9148-EBZ | 功能描述:BOARD EVALUATION FOR AD9148 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:TxDAC+® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
發布緊急采購，3分鐘左右您將得到回復。