參數資料
型號： 935268252551
廠商： NXP SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： 1 CHANNEL(S), 400M bps, SERIAL COMM CONTROLLER, PQFP144
封裝： 20 X 20 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT-486-1, LQFP-144
文件頁數： 50/80頁
文件大?。?/td> 306K
代理商： 935268252551
Philips Semiconductors
Preliminary specification
PDI1394L40
1394 enhanced AV link layer controller
2000 Dec 15
51
13.2
AV (Isochronous) Transmitter and Receiver Registers
13.2.1
Isochronous Transmit Packing Control and Status (ITXPKCTL) – Base Address: 0x020
This register allows the user to set up the appropriate AV packets from data entered into the AV interface. The packing and control parameters
(TRDEL, MAXBL, DBS, FN, QPC, and SPH) should never be changed while the transmitter is operating. The only exception to this is the
MAXBL parameter when in MPEG-2 packing mode.
NOTE: When reset of isochronous transmitter is necessary, first disable the transmitter (place bit 4, EN_ITX, LOW), wait for FIFO to empty, then
reset the transmitter (place RST_ITX, bit 0, HIGH). This procedure will ensure that data in the FIFO is transmitted before reset.
29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
EN_ITX
EN_FS
RST_ITX
SV00886
PM
TRDEL
MAXBL
31 30
TXAP_CLK
SYT_DELA
Y
ENXTMSTP
AUDIO
Reset Value 0x00000001
Bit 30:
R/W
AUDIO mode bit: When = 1, SYT system is in AUDIO mode. When AUDIO = 0 normal SYT time stamping operation is
assumed. With AUDIO = 1, the SYT time stamp for an FSYNC pulse will NOT be appended to an empty bus packet.
Any pending SYT stamp will be held until the next non-empty bus packet is sent. As an FSYNC pulse is input to the
transmitting node’s link chip, an SYT stamp will be made. This SYT stamp will point to a time in the future dictated by
the SYT DELAY value (in register 0x020) added to the current least significant nibble (lsn) of the cycle number, plus
the current cycle offset value. This mode automatically increases SYT_DELAY value by two additional cycles beyond
the value programmed in the SYT_DELAY bits.
Bit 29..28:
R/W
TXAP_CLK: Application Clock, default mode, ‘00’ the AVxCLK pin is an input. This pin can become an application
clock for the isochronous Transmitter (and output) by programming it to ‘01’, ‘10’, or ‘11’.
The programming values are:
00
Input
01
24.576MHz
10
12.288MHz
11
6.144MHz
Note that when enabled as ‘01’, ‘10’, or ‘11’, the AV port that is configured as transmitter and enabled will output this
clock signal on its AVxCLK pin.
Bit 27..16:
R/W
TRDEL: Transport delay. Value added to cycle timer to produce time stamps. Lower 4 bits add to upper 4 bits of
cycle_offset, (Cycle Timer Register, CYCTM). Remainder adds to cycle_count field.
Bit 15..8:
R/W
MAXBL: The (maximum) number of data blocks to be put in a payload.
Bit 7:
R/W
ENXTMSTP: Enable External time stamp control. Allows an external time stamp (generated by the application) to
be inserted in place of the link-generated time stamp. Defaults to link generated time stamp. The application must
present the first byte of a quadlet-wide time stamp accompanied by the AVSYNC pulse (and AVVALID) to the
AVPORT. The external time stamp quadlet is inputted first, followed by the application data packet. The transmitted
packet size is now one quadlet larger than the original isochronous data packet—Set up the isochronous transmitter
accordingly with SPH = 1. CAUTION: Unless valid IEC 61883 time stamp format (based on the link cycle timer)
is used, the receiving node link chip must be equipped with a time stamp check disabling function similar to the
DIS_TSC bit (register 0x040, Bit 7). Please see section 13.2.8 for details.
Bit 6..5:
R/W
SYT_DELAY: Programmable delay of AV1FSYNC and AV2FSYNC. Each cycle is 1 bus cycle, 125
ms.
Reset value is “00”, a 3 cycle delay.
01 = 2 cycles
00 = 3 cycles
10 = 4 cycles
11 = Reserved
Bit 4:
R/W
EN_ITX: Enable receipt of new application packets and generation of isochronous bus packets in every cycle. This bit
also enables the Link Layer to arbitrate for the transmitter in each subsequent bus cycle. When this bit is disabled (0),
the current packet will be transmitted and then the transmitter will shut down.
Bit 3..2:
R/W
PM: packing mode:
00 = variable sized bus packets, most generic mode.
01 = fixed size bus packets.
10 = MPEG–2 packing mode.
11 = No data, just CIP headers are transmitted.
Bit 1:
R/W
EN_FS:enable generation/insertion of SYT stamps (Time Stamps) in CIP header.
Bit 0:
R/W
Reset Isochronous Transmitter (RST_ITX): causes transmitter to be reset when ‘1’. In order for synchronous reset of
ITX to work properly, an AVxCLK (from either the internal or external source) must be present and ensure that the
reset bit is kept (programmed) HIGH for at least the duration of one AVxCLK period. Failure to do so may cause the
application interface of this module to be improperly reset (or not reset at all). When reset is enabled, all bytes will
be flushed from the FIFO and transmission will cease immediately.
相關PDF資料
PDF描述
08008GOC 125 A, 800 V, SCR, TO-209AC
08008GOD 125 A, 800 V, SCR, TO-208AD
08010GOB 125 A, 1000 V, SCR, TO-209AC
08010GOC 125 A, 1000 V, SCR, TO-209AC
08010GOD 125 A, 1000 V, SCR, TO-208AD
相關代理商/技術參數
參數描述
935268721125 制造商:NXP Semiconductors 功能描述:Buffer/Line Driver 1-CH Non-Inverting 3-ST CMOS 5-Pin TSSOP T/R
935269304128 制造商:ST-Ericsson 功能描述:IC AUDIO CODEC W/TCH SCRN 48LQFP
935269544557 制造商:NXP Semiconductors 功能描述:SUB ONLY TDA9587-2US1-V1.3
935269987557 制造商:NXP Semiconductors 功能描述:SUB ONLY TDA9587-1US1-V1.8 SUBBED TO 935269987557
935270713557 制造商:NXP Semiconductors 功能描述:SUB ONLY IC CHP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*