- 您現在的位置：買賣IC網 > PDF目錄358620 > 30044-23 (NATIONAL SEMICONDUCTOR CORP) Low Power Integrated x86-Compatible with MMX Support 32-Bit Geode GXm Processor(低功耗集成兼容X86帶有MMX的32位 Geode GXm技術處理器) PDF資料下載
參數資料
| 型號： | 30044-23 |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Low Power Integrated x86-Compatible with MMX Support 32-Bit Geode GXm Processor(低功耗集成兼容X86帶有MMX的32位 Geode GXm技術處理器) |
| 中文描述： | 32-BIT, 200 MHz, MICROPROCESSOR, CPGA320 |
| 封裝： | SPGA-320 |
| 文件頁數： | 86/244頁 |
| 文件大?。?/td> | 4496K |
| 代理商： | 30044-23 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁當前第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁第243頁第244頁
www.national.com
86
Revision 3.1
Processor Programming (
Continued
)
G
3.12 SHUTDOWN AND HALT
The Halt Instruction (HLT) stops program execution and
generates a special Halt bus cycle. The GXm processor
core then drives out a special Stop Grant bus cycle and
enters a low-power Suspend mode if the SUSP_HLT bit in
CCR2 (Index C2h[3]) is set. SMI#, NMI, INTR with inter-
rupts enabled (IF bit in EFLAGS = 1), or RESET forces
the CPU out of the halt state. If the halt state is inter-
rupted, the saved code segment and instruction pointer
specify the instruction following the HLT.
Shutdown occurs when a severe error is detected that
prevents further processing. The most common severe
error is the triple fault, a fault event while handling a dou-
ble fault. Setting the IDT or the GDT limit to zero will
cause a triple fault.
An NMI input or a reset can bring the processor out of
shutdown. An NMI will work if the IDT limit is large
enough, at least 000Fh, to contain the NMI interrupt vec-
tor and if the stack has enough room. The stack must be
large enough to contain the vector and flag information
(the stack pointer must be greater than 0005h).
3.13 PROTECTION
Segment protection and page protection are safeguards
built into the GXm processor’s protected-mode architec-
ture that deny unauthorized or incorrect access to
selected memory addresses. These safeguards allow
multitasking programs to be isolated from each other and
from the operating system. This section concentrates on
segment protection.
Selectors and descriptors are the key elements in the seg-
ment protection mechanism. The segment base address,
size, and privilege level are established by a segment
descriptor. Privilege levels control the use of privileged
instructions, I/O instructions and access to segments and
segment descriptors. Selectors are used to locate seg-
ment descriptors.
Segment accesses are divided into two basic types, those
involving code segments (e.g., control transfers) and
those involving data accesses. The ability of a task to
access a segment depends on the:
segment type
instruction requesting access
type of descriptor used to define the segment
associated privilege levels (described next)
Data stored in a segment can be accessed only by code
executing at the same or a more privileged level. A code
segment or procedure can only be called by a task exe-
cuting at the same or a less privileged level.
3.13.1 Privilege Levels
The values for privilege levels range between 0 and 3.
Level 0 is the highest privilege level (most privileged), and
level 3 is the lowest privilege level (least privileged). The
privilege level in real mode is zero.
The
Descriptor Privilege Level
(DPL) is the privilege
level defined for a segment in the segment descriptor. The
DPL field specifies the minimum privilege level needed to
access the memory segment pointed to by the descriptor.
The
Current Privilege Level
(CPL) is defined as the cur-
rent task’s privilege level. The CPL of an executing task is
stored in the hidden portion of the code segment register
and essentially is the DPL for the current code segment.
The
Requested Privilege Level
(RPL) specifies a selec-
tor’s privilege level. RPL is used to distinguish between
the privilege level of a routine actually accessing memory
(the CPL), and the privilege level of the original requester
(the RPL) of the memory access. If the level requested by
RPL is less than the CPL, the RPL level is accepted and
the Effective Privilege Level (EPL) is changed to the RPL
value. If the level requested by RPL is greater than CPL,
the CPL overrides the requested RPL and EPL becomes
the CPL value.
The lesser of the RPL and CPL is called the Effective Privi-
lege Level (EPL). Therefore, if RPL = 0 in a segment selec-
tor, the EPL is always determined by the CPL. If RPL = 3,
the EPL is always 3 regardless of the CPL.
For a memory access to succeed, the EPL must be at
least as privileged as the Descriptor Privilege Level (EPL
≤
DPL). If the EPL is less privileged than the DPL (EPL >
DPL), a general protection fault is generated. For exam-
ple, if a segment has a DPL = 2, an instruction accessing
the segment only succeeds if executed with an EPL
≤
2.
3.13.2 I/O Privilege Levels
The I/O Privilege Level (IOPL) allows the operating sys-
tem executing at CPL = 0 to define the least privileged
level at which IOPL-sensitive instructions can uncondition-
ally be used. The IOPL-sensitive instructions include CLI,
IN, OUT, INS, OUTS, REP INS, REP OUTS, and STI.
Modification of the IF bit in the EFLAGS register is also
sensitive to the I/O privilege level.
The IOPL is stored in the EFLAGS register (bits [31:12]).
An I/O permission bit map is available as defined by the
32-bit Task State Segment (TSS). Since each task can
have its TSS, access to individual I/O ports can be
granted through separate I/O permission bit maps.
If CPL
≤
IOPL, IOPL-sensitive operations can be per-
formed. If CPL > IOPL, a general protection fault is gener-
ated if the current task is associated with a 16-bit TSS. If
the current task is associated with a 32-bit TSS and CPL
> IOPL, the CPU consults the I/O permission bitmap in the
TSS to determine on a port-by-port basis whether or not I/O
instructions (IN, OUT, INS, OUTS, REP INS, REP OUTS)
are permitted. The remaining IOPL-sensitive operations
generate a general protection fault.
相關PDF資料 |
PDF描述 |
|---|---|
| 30046-23 | Low Power Integrated x86-Compatible 32-Bit Geode GXLV Processor(低功耗集成兼容X86的32位 Geode GXLV技術處理器) |
| 300471U | Radial, -55dotc, long life wsitching-power |
| 300CNQ | SCHOTTKY RECTIFIER |
| 300CNQ035 | SCHOTTKY RECTIFIER |
| 300CNQ040 | SCHOTTKY RECTIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 3004430 | 功能描述:DIN導軌式接線端子 UK 5-MTK RoHS:否 制造商:Phoenix Contact 類型:Feed Through Modular Terminal Block 位置/觸點數量:1 線規量程:26-14 電流額定值:5 A, 15 A 電壓額定值:300 V, 600 V 安裝風格: 端接類型:Push-In |
| 30044-44L | 制造商:LENOX 功能描述:HOLE SAW BI-METAL 70MM |
| 3004472 | 制造商:Phoenix Contact 功能描述:UK 5-HESI (5X20) |
| 300448 | 功能描述:手工工具 RETAINING PIN RoHS:否 制造商:Molex 產品:Extraction Tools 類型: 描述/功能:Extraction tool |
| 300449 | 制造商:MACOM 制造商全稱:Tyco Electronics 功能描述:HAND TOOL ASSEMBLY |
發布緊急采購，3分鐘左右您將得到回復。