- 您現在的位置：買賣IC網 > PDF目錄371435 > 28F3204W30 (Intel Corp.) 1.8 Volt Intel Wireless Flash Memory with 3 Volt I/O and SRAM (W30) PDF資料下載
參數資料
| 型號： | 28F3204W30 |
| 廠商： | Intel Corp. |
| 元件分類： | DRAM |
| 英文描述： | 1.8 Volt Intel Wireless Flash Memory with 3 Volt I/O and SRAM (W30) |
| 中文描述： | 1.8伏英特爾無線閃存的3伏的I / O和SRAM（寬30） |
| 文件頁數： | 11/82頁 |
| 文件大?。?/td> | 749K |
| 代理商： | 28F3204W30 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁
28F6408W30, 28F3204W30, 28F320W30, 28F640W30
Preliminary
5
2.4
Signal Descriptions
Table 2. Signal Descriptions (Sheet 1 of 2)
Symbol
Type
Name and Function
A
25
–
0
I
ADDRESS:
Device address. Addresses are internally latched during read and write cycles.
32-Mbit flash: A
20
–
0
; 64-Mbit flash: A
21
–
0
; 128-Mbit flash: A
22
–
0
; 4-Mbit SRAM: A
17
–
0
; 8-Mbit SRAM: A
18
–
0
DQ
15
–
0
I/O
DATA INPUT/OUTPUTS:
Inputs data and commands during write cycles, outputs data during query, id
reads, memory, status register, protection register, and configuration code reads. Data signals float when
the chip or outputs are deselected. Data is internally latched during writes. Query accesses and status
register accesses use DQ
0
–
DQ
7
. All other accesses use DQ
0
–
DQ
15
.
ADV#
I
FLASH ADDRESS VALID:
Internally latches addresses. In page mode, addresses are internally latched on
the rising edge of ADV#. In burst mode, address internally latched on the rising edge of ADV# or rising/
falling edge of CLK, whichever occurs first. Connect ADV# to GND when the flash device is operating in
asynchronous mode only.
CE#
I
FLASH CHIP ENABLE:
Enables/disables flash device. CE#-low enables the device. CE#-high disables the
device and places the device into standby mode. CE# high places data and WAIT signals at a High-Z level.
S-CS
1
#
I
SRAM CHIP SELECT1:
Activates the SRAM internal control logic, input buffers, decoders and sense
amplifiers. S-CS
1
# is active low. S-CS
1
# high deselects the SRAM memory device and reduces power
consumption to standby levels.
S-CS
2
I
SRAM CHIP SELECT2:
Activates the SRAM internal control logic, input buffers, decoders and sense
amplifiers. S-CS
2
is active high. S-CS
2
low deselects the SRAM memory device and reduces power
consumption to standby levels.
CLK
I
FLASH CLOCK:
Synchronizes the device to the system bus frequency. (Used only in burst mode.)
OE#
I
FLASH OUTPUT ENABLE:
Enables/disables device output buffers. OE# low enables the device output
buffers. OE# high disables the device output buffers and places all outputs at a High-Z level.
S-OE#
I
SRAM OUTPUT ENABLE:
Activates the SRAM outputs through the data buffers during a read operation.
S-OE# is active low.
RST#
I
FLASH RESET:
Enables/disables device operation. RST# low initializes internal circuitry and disables
device operation. RST# high enables device operation.
WAIT
O
FLASH WAIT:
Indicates valid data in burst read mode. WAIT is at High-Z until the configuration register bit
CR.10 is set, which also determines its polarity when asserted.
WE#
I
FLASH WRITE ENABLE:
Enables/disables device write buffers. WE# low enables the device write buffers.
Data is latched on the rising edge of WE#. WE# high disables the device write buffers.
S-WE#
I
SRAM WRITE ENABLE:
Controls writes to the SRAM memory array. S-WE# is active low.
S-UB#
I
SRAM UPPER BYTE ENABLE:
Enables the upper bytes for SRAM (DQ
15-8
). S-UB# is active low. S-UB#
and S-LB# must be tied together to restrict x16 mode.
S-LB#
I
SRAM LOWER BYTE ENABLE:
Enables the lower bytes for SRAM (DQ
7-0
). S-LB# is active low. S-UB#
and S-LB# must be tied together to restrict x16 mode.
WP#
I
FLASH WRITE PROTECT:
Enables/disables the device lock-down function. WP# low enables the lock-
down mechanism and blocks marked lock-down cannot be unlocked by system software. WP# high
disables the lock-down mechanism and blocks marked lock-down can be unlocked by system software.
V
PP
Pwr
FLASH PROGRAM/ERASE POWER:
Hardware erase and program protection. A valid V
PP
voltage on this
ball allows erase or programming. Memory contents cannot be altered when V
PP
< V
PPLK
. Block erase and
program at invalid V
PP
voltages should not be attempted. Set V
PP
= V
CC
for in-system read, program, and
erase operations. V
PP
must remain above V
PP1
Min to perform in-system operations. V
PP2
can be applied to
main blocks for 1000 cycles maximum and to parameter blocks for 2500 cycles.
V
PP
can be V
PP2
for a
cumulative total, not to exceed 80 hours maximum. Extended use of this ball at V
PP2
may reduce block
cycling capability.
V
CC
Pwr
FLASH POWER SUPPLY:
Flash operations at invalid V
CC
voltages should not be attempted.
V
CCQ
Pwr
FLASH OUTPUT POWER SUPPLY:
Enables all input and output signals to be driven at V
CCQ
.
相關PDF資料 |
PDF描述 |
|---|---|
| 28F320W30 | 1.8 Volt Intel Wireless Flash Memory with 3 Volt I/O and SRAM (W30) |
| 28F6408W30 | 1.8 Volt Intel Wireless Flash Memory with 3 Volt I/O and SRAM (W30) |
| 28F640W30 | 1.8 Volt Intel Wireless Flash Memory with 3 Volt I/O and SRAM (W30) |
| 28F320B3 | SMART 3 ADVANCED BOOT BLOCK 4-, 8-, 16-, 32-MBIT FLASH MEMORY FAMILY |
| 28F640P3 | Intel StrataFlash Embedded Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 28F320B3 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:SMART 3 ADVANCED BOOT BLOCK 4-, 8-, 16-, 32-MBIT FLASH MEMORY FAMILY |
| 28F320C3 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Advanced+ Boot Block Flash Memory (C3) |
| 28F320J3D75 | 制造商:undefined 功能描述: |
| 28F320J5 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:StrataFlash MEMORY TECHNOLOGY 32 AND 64 MBIT |
| 28F320J5_02 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:5 Volt Intel StrataFlash? Memory |
發布緊急采購，3分鐘左右您將得到回復。