參數資料
型號: ZL30109QDG1
廠商: ZARLINK SEMICONDUCTOR INC
元件分類: 通信及網絡
英文描述: DS1/E1 System Synchronizer with
中文描述: SPECIALTY TELECOM CIRCUIT, PQFP64
封裝: 10 X 10 MM, 1 MM HEIGHT, LEAD FREE, MS-026ACD, TQFP-64
文件頁數: 21/37頁
文件大小: 751K
代理商: ZL30109QDG1
ZL30109
Data Sheet
21
Zarlink Semiconductor Inc.
Figure 11 - Reference Switching in Normal Mode
5.0 Measures of Performance
The following are some PLL performance indicators and their corresponding definitions.
5.1 Jitter
Timing jitter is defined as the high frequency variation of the clock edges from their ideal positions in time. Wander
is defined as the low-frequency variation of the clock edges from their ideal positions in time. High and low
frequency variation imply phase oscillation frequencies relative to some demarcation frequency. (Often 10 Hz or
20 Hz for DS1 or E1, higher for SONET/SDH clocks.) Jitter parameters given in this data sheet are total timing jitter
numbers, not cycle-to-cycle jitter.
5.2 Jitter Generation (Intrinsic Jitter)
Jitter generation is the measure of the jitter produced by the PLL and is measured at its output. It is measured by
applying a reference signal with no jitter to the input of the device, and measuring its output jitter. Jitter generation
may also be measured when the device is in a non-synchronizing mode, such as free running or holdover, by
measuring the output jitter of the device. Jitter generation is usually measured with various bandlimiting filters
depending on the applicable standards.
5.3 Jitter Tolerance
Jitter tolerance is a measure of the ability of a PLL to operate properly (i.e., remain in lock and or regain lock in the
presence of large jitter magnitudes at various jitter frequencies) when jitter is applied to its reference. The applied
jitter magnitude and jitter frequency depends on the applicable standards.
5.4 Jitter Transfer
Jitter transfer or jitter attenuation refers to the magnitude of jitter at the output of a device for a given amount of jitter
at the input of the device. Input jitter is applied at various amplitudes and frequencies, and output jitter is measured
with various filters depending on the applicable standards.
For the Zarlink digital PLLs two internal elements determine the jitter attenuation; the internal low pass loop filter
and the phase slope limiter. The phase slope limiter limits the output phase slope to, for example, 61
μ
s/s.
Therefore, if the input signal exceeds this rate, such as for very large amplitude low frequency input jitter, the
maximum output phase slope will be limited (i.e., attenuated).
Since intrinsic jitter is always present, jitter attenuation will appear to be lower for small input jitter signals than for
large ones. Consequently, accurate jitter transfer function measurements are usually made with large input jitter
signals (for example 75% of the specified maximum tolerable input jitter).
REF1
REF0
REF_SEL
LOCK
Lock Time
Note: LOCK pin behaviour depends on phase and frequency offset of REF1.
相關PDF資料
PDF描述
ZL30109 DS1/E1 System Synchronizer with 19.44 MHz Output
ZL30109QDG DS1/E1 System Synchronizer with 19.44 MHz Output
ZL30110 Telecom Rate Conversion DPLL
ZL30110LDE Telecom Rate Conversion DPLL
ZL30110LDE1 Telecom Rate Conversion DPLL
相關代理商/技術參數
參數描述
ZL30110 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Telecom Rate Conversion DPLL
ZL30110LDE 制造商:Microsemi Corporation 功能描述: 制造商:Microsemi Corporation 功能描述:PLL FREQ SYNTHESIZER TRIPLE 32QFN - Rail/Tube
ZL30110LDE1 制造商:Microsemi Corporation 功能描述:
ZL30110LDF1 制造商:Microsemi Corporation 功能描述:PB FREE TELECOM RATE CONVERSION DPLL - Tape and Reel 制造商:Zarlink Semiconductor Inc 功能描述:PB FREE TELECOM RATE CONVERSION DPLL - Tape and Reel
ZL30110LDG1 制造商:Microsemi Corporation 功能描述:PB FREE TELECOM RATE CONVERSION DPLL - Trays 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC DPLL RATE CONVERSION 32QFN 制造商:Microsemi Corporation 功能描述:IC DPLL RATE CONVERSION 32QFN