參數資料
型號： XRT73L04BIV-F
廠商： Exar Corporation
文件頁數： 31/64頁
文件大?。?/td> 0K
描述： IC LIU E3/DS3/STS-1 4CH 144LQFP
標準包裝： 60
類型： 線路接口裝置（LIU）
驅動器/接收器數： 4/4
規程： DS3，E3，STS-1
電源電壓： 3.135 V ~ 3.465 V
安裝類型： 表面貼裝
封裝/外殼： 144-LQFP
供應商設備封裝： 144-LQFP（20x20）
包裝： 托盤
XRT73L04B
4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
REV. 1.0.1
33
2.4.3
Design Guideline for Setting the Transmit
Line Build-Out Circuit
The TxLEV_(n) input pins or bit-fields should be set
based upon the overall cable length between the
Transmitting Terminal and the Digital Cross Connect
system where the pulse template measurements are
made.
If the cable length between the Transmitting Ter-
minal and the DSX-3 or STSX-1 is less than 225
feet, enable the Transmit Line Build-Out circuit by
setting the TxLEV_(n) input pin or bit-field to "0".
NOTE: In this case, the configured channel outputs shaped
(e.g., not square-wave) pulses onto the line via its TTIP_(n)
and TRing_(n) output pins. The shape of this output pulse
is such that it complies with the pulse template require-
ments even when subjected to cable loss ranging from 0 to
225 feet.
If the cable length between the Transmitting Ter-
minal and the DSX-3 or STSX-1 is greater than 225
feet, disable the Transmit Line Build-Out circuit
by setting the TxLEV_(n) input pin or bit-field to
"1".
NOTE: In this case, the configured channel outputs partially
shaped pulses onto the line via the TTIP_(n) and TRing_(n)
output pins. The cable loss that these pulses experience
over long cable lengths (e.g., greater than 225 feet) cause
these pulses to be properly shaped and comply with the
appropriate pulse template requirement.
2.4.4
The Transmit Line Build-Out Circuit and
E3 Applications
The ITU-T G.703 Pulse Template Requirements for
E3 states that the E3 transmit output pulse should be
measured at the Secondary Side of the Transmit Out-
put Transformer for Pulse Template compliance. In
other words, there is no Digital Cross Connect Sys-
tem pulse template requirement for E3. Consequent-
ly, the Transmit Line Build-Out circuit within a given
Channel is disabled whenever that channel has been
configured to operate in the E3 Mode.
2.5
INTERFACING THE TRANSMIT SECTIONS OF THE
XRT73L04B TO THE LINE
The E3, DS3 and SONET STS-1 specification docu-
ments all state that line signals transmitted over coax-
ial cable are to be terminated with 75 Ohm resistor.
Interface the Transmit Section of the XRT73L04B in
the manner illustrated in Figure 21.
COMMAND REGISTER, CR1-(n)
D4
D3
D2
D1
D0
TxOFF_(n)
TAOS_(n)
TxClkINV_(n)
TxLEV_(n)
Reserved
0X
X
1X
FIGURE 21. RECOMMENDED SCHEMATIC FOR INTERFACING THE TRANSMIT SECTION OF THE XRT73L04B TO
THE
LINE
R1
31.6
R2
31.6
Channel (n)
TxPOS_(n)
TxNEG_(n)
TxLineClk_(n)
TTIP_(n)
TRing_(n)
TPData_(n)
TNData_(n)
TxClk_(n)
Only One Channel Shown
1:1
J1
BNC
相關PDF資料
PDF描述
XRT73L06IB-F IC LIU E3/DS3/STS-1 6CH 217BGA
XRT73LC00AIV-F IC LIU STS1/DS3/E3 SGL 44TQFP
XRT73LC03AIV-F IC LIU E3/DS3/STS-1 3CH 120LQFP
XRT73LC04AIV-F IC LIU E3/DS3/STS-1 4CH 144LQFP
XRT73R06IB-F IC LIU E3/DS3/STS-1 6CH 217BGA
相關代理商/技術參數
參數描述
XRT73L06 制造商:EXAR 制造商全稱:EXAR 功能描述:SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT
XRT73L06ES 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT73L06IB 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT73L06IB-F 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
XRT73L06IQ 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecomm/Datacomm
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*