- 您現在的位置：買賣IC網 > PDF目錄4214 > XCV405E-7FG676I (Xilinx Inc)IC FPGA 1.8V 676-BGA PDF資料下載
參數資料
| 型號： | XCV405E-7FG676I |
| 廠商： | Xilinx Inc |
| 文件頁數： | 34/118頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC FPGA 1.8V 676-BGA |
| 產品變化通告： | FPGA Family Discontinuation 18/Apr/2011 |
| 標準包裝： | 1 |
| 系列： | Virtex®-E EM |
| LAB/CLB數： | 2400 |
| 邏輯元件/單元數： | 10800 |
| RAM 位總計： | 573440 |
| 輸入/輸出數： | 404 |
| 門數： | 129600 |
| 電源電壓： | 1.71 V ~ 1.89 V |
| 安裝類型： | 表面貼裝 |
| 工作溫度： | -40°C ~ 100°C |
| 封裝/外殼： | 676-BGA |
| 供應商設備封裝： | 676-FBGA（27x27） |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁
Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays
Module 2 of 4
DS025-2 (v3.0) March 21, 2014
18
R
— OBSOLETE — OBSOLETE — OBSOLETE — OBSOLETE —
Configuration through the TAP uses the CFG_IN instruc-
tion. This instruction allows data input on TDI to be con-
verted into data packets for the internal configuration bus.
The following steps are required to configure the FPGA
through the boundary-scan port (when using TCK as a
start-up clock).
1.
Load the CFG_IN instruction into the boundary-scan
instruction register (IR)
2.
Enter the Shift-DR (SDR) state
3.
Shift a configuration bitstream into TDI
4.
Return to Run-Test-Idle (RTI)
5.
Load the JSTART instruction into IR
6.
Enter the SDR state
7.
Clock TCK through the startup sequence
8.
Return to RTI
Configuration and readback via the TAP is always available.
The boundary-scan mode is selected by a <101> or <001>
on the mode pins (M2, M1, M0). For details on TAP charac-
teristics, refer to XAPP139.
Configuration Sequence
The configuration of Virtex-E devices is a three-phase pro-
cess. First, the configuration memory is cleared. Next, con-
figuration data is loaded into the memory, and finally, the
logic is activated by a start-up process.
Configuration is automatically initiated on power-up unless
it is delayed by the user, as described below. The configura-
tion process can also be initiated by asserting PROGRAM.
The end of the memory-clearing phase is signalled by INIT
going High, and the completion of the entire process is sig-
nalled by DONE going High.
The power-up timing of configuration signals is shown in
The corresponding timing characteristics are listed in
Delaying Configuration
INIT can be held Low using an open-drain driver. An
open-drain is required since INIT is a bidirectional
open-drain pin that is held Low by the FPGA while the con-
figuration memory is being cleared. Extending the time that
the pin is Low causes the configuration sequencer to wait.
Thus, configuration is delayed by preventing entry into the
phase where data is loaded.
Start-Up Sequence
The default Start-up sequence is that one CCLK cycle after
DONE goes High, the global 3-state signal (GTS) is
released. This permits device outputs to turn on as neces-
sary.
One CCLK cycle later, the Global Set/Reset (GSR) and
Global Write Enable (GWE) signals are released. This per-
Figure 20: Power-Up Timing Configuration Signals
VALI
PROGRAM
Vcc
CCLK OUTPUT or INPUT
M0, M1, M2
(Required)
TPL
TICCK
ds022_020_071201
TPOR
INIT
Table 12:
Power-up Timing Characteristics
Description
Symbol
Value
Units
Power-on Reset1
TPOR
2.0
ms, max
Program Latency
TPL
100.0
μs, max
CCLK (output) Delay
TICCK
0.5
μs, min
4.0
μs, max
Program Pulse Width
TPROGRAM
300
ns, min
Notes:
1.
TPOR delay is the initialization time required after VCCINT
reaches the recommended operating voltage.
相關PDF資料 |
PDF描述 |
|---|---|
| XC6VLX195T-1FFG784C | IC FPGA VIRTEX 6 199K 784FFGBGA |
| XC6VCX130T-2FFG784I | IC FPGA VIRTEX 6 128K 784FFGBGA |
| XC4VLX60-11FF668I | IC FPGA VIRTEX-4LX 668FFBGA |
| XC4VLX60-12FFG668C | IC FPGA VIRTEX-4 LX 60K 668FCBGA |
| XC4VLX60-11FFG668I | IC FPGA VIRTEX-4 LX 60K 668FCBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XCV405E-7FG900C | 制造商:XILINX 制造商全稱:XILINX 功能描述:Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays |
| XCV405E-7FG900I | 制造商:XILINX 制造商全稱:XILINX 功能描述:Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays |
| XCV405E-8BG404C | 制造商:XILINX 制造商全稱:XILINX 功能描述:Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays |
| XCV405E-8BG404I | 制造商:XILINX 制造商全稱:XILINX 功能描述:Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays |
| XCV405E-8BG556C | 制造商:XILINX 制造商全稱:XILINX 功能描述:Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays |
發布緊急采購，3分鐘左右您將得到回復。