- 您現在的位置：買賣IC網 > PDF目錄68449 > W28J161BB90L (WINBOND ELECTRONICS CORP) 1M X 16 FLASH 3V PROM, 90 ns, PBGA48 PDF資料下載
參數資料
| 型號： | W28J161BB90L |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | PROM |
| 英文描述： | 1M X 16 FLASH 3V PROM, 90 ns, PBGA48 |
| 封裝： | 8 X 8 MM, 0.75 MM PITCH, TFBGA-48 |
| 文件頁數： | 8/43頁 |
| 文件大?。?/td> | 1333K |
| 代理商： | W28J161BB90L |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
W28J161B/T
- 16 -
(see Figure 8). VPP must remain at VPPH1/2 (the same VPP level used for block erase) while block erase
is suspended. #RESET must also remain at VIH. #WP must also remain at VIL or VIH (the same #WP
level used for block erase). Block erase cannot resume until word write operations initiated during
block erase suspend have completed.
If the time from Block Erase Resume command write to the CUI till Block Erase Suspend command
write to the CUI is short, it can be repeated. In addition, erase time be prolonged.
Word Write Suspend Command
The Word Write Suspend command allows word write interruption to read data in other flash memory
locations. Once the word write process starts, sending the Word Write Suspend command causes
the WSM to suspend the Word write sequence at a predetermined point in the algorithm. The device
continues to output status register data when read after the Word Write Suspend command is written.
Polling status register bits SR.7 and SR.2 can determine when the word write operation has been
suspended (both will be set to "1"). The period tWHR11 defines the word write suspend latency
parameters.
When Word Write Suspend command writes to the CUI, the device is placed in read array mode if
word write is finished. Therefore, after Word Write Suspend command writes to the CUI, the Read
Status Register command (70H) has to write to CUI, then status register bit SR.2 should be checked
to confirm the device is in suspend mode.
At this point, a Read Array command can be written to read data from locations other than that which
is suspended. The only other valid commands while word write is suspended are Read Status
Register and Word Write Resume. After Word Write Resume command is written to the flash memory,
the WSM will continue the word write process. Status register bits SR.2 and SR.7 will automatically
clear. After the Word Write Resume command is written, the device automatically outputs status
register data when read (see Figure 9). VPP must remain at VPPH1/2 (the same VPP level used for word
write) while in word write suspend mode. #RESET must also remain at VIH. #WP must also remain at
VIL or VIH (the same #WP level used for word write).
If the period from Word Write Resume command write to Word Write Suspend command write is too
short, it can be repeated, and the write time will be prolonged.
Set Block and Permanent Lock-Bit Commands
A flexible block locking and unlocking scheme is enabled via a combination of block lock-bits, a
permanent lock-bit and #WP pin. The block lock-bits and #WP pin gates program and erase
operations while the permanent lock-bit gates block-lock bit modification. With the permanent lock-bit
not set, individual block lock-bits can be set using the Set Block Lock-Bit command. The Set
Permanent Lock-Bit command sets the permanent lock-bit. After the permanent lock-bit is set, block
lock-bits and locked block contents cannot be altered. See Table 5 for a summary of hardware and
software write protection options.
Set block lock-bit and permanent lock-bit are executed by a two-cycle command sequence. The set
block or permanent lock-bit setup along with appropriate block or device address is written followed by
either the set block lock-bit confirm (and an address within the block to be locked) or the set
permanent lock-bit confirm (and any device address). The WSM then executes the set lock-bit
algorithm. After the sequence is written, the device automatically outputs status register data when
read (see Figure 10). The CPU can detect the completion of the set lock-bit event by analyzing the
status register bit SR.7.
相關PDF資料 |
PDF描述 |
|---|---|
| W28J321BB90L | 2M X 16 FLASH 2.7V PROM, 90 ns, PBGA48 |
| W29C010MP90B | 128K X 8 FLASH 5V PROM, 90 ns, PQCC32 |
| W29C010MP90 | 128K X 8 FLASH 5V PROM, 90 ns, PQCC32 |
| W29C011AP15N | 128K X 8 FLASH 5V PROM, 150 ns, PQCC32 |
| W29C020CP-12 | 256K X 8 FLASH 5V PROM, 120 ns, PQCC32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W28NK60Z | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:N-CHANNEL 600 V - 0.155з - 27A TO-247 Zener-Protected SuperMESH MOSFET |
| W28-SQ11A-10 | 功能描述:CIRCUIT BREAK 10A W/SWITCH RoHS:否 類別:過電壓，電流，溫度裝置 >> 斷路器 系列:W28 標準包裝:3 系列:AS168X 斷路器類型:熱磁動式 電壓:65VDC，277/480VAC 電流 - 跳閘(It):30A 極數:3 觸動器類型:按片 安裝類型:DIN 軌道 其它名稱:4420.02104420.0210-ND486-2338AS168X-CB3G300-NDCBE AS168X-CB3G300 |
| W28-SQ11A-15 | 制造商:TE Connectivity 功能描述: |
| W28-SQ11A-3 | 制造商:TE Connectivity 功能描述:Circuit Breaker Thermal 1Pole 3A 250VAC/32VDC |
| W28-SQ11A-5 | 制造商:TE Connectivity 功能描述:Circuit Breaker Thermal 1Pole 5A 250VAC/32VDC |
發布緊急采購，3分鐘左右您將得到回復。