參數資料
型號： UPD7554AGA
廠商： NEC Corp.
英文描述： 4-BIT SINGLE-CHIP MICROCOMPUTER
中文描述： 4位單片機
文件頁數： 24/64頁
文件大小： 991K
代理商： UPD7554AGA
24
μ
PD7554A, 7554A(A)
The serial interface sets serial data for transmission in the shift register using the TAMSIO instruction and starts
the transfer using the SIO instruction. To recognize the termination of one-byte transfer, check the test request flag
INT0/S RQF using the corresponding instruction.
The serial interface starts serial data reception, using the SIO instruction, checks the termination of one-byte
transfer using the instruction, and then receives data from the shift register by executing the TSIOAM instruction.
Two types of serial clock sources are available: one is the system clock
φ
and the other is the external clock (SCK
input). They are selected respectively by bits 2 and 1 (SM2 and SM1) of the shift mode register.
When the system clock
φ
is selected and the SIO instruction is executed, the clock pulse is supplied to the serial
interface as a serial clock to control serial data input/output and is output from the SCK pin.
When the system clock
φ
pulse is supplied eight times, the supply to the serial interface is automatically stopped
and the SCK output remains high. Since serial data input/output stops automatically after transfer of one byte. The
programmer does not need to control the serial clock. In this case, the transfer speed is determined by the system
clock frequency.
In this mode, it is possible to read receive data (by the TSIOAM instruction) and write data (by the TAMSIO
instruction) from and to the shift register only by waiting for 6 machine cycles after execution of the SIO instrucction
on the program without waiting until the INT0/S RQF is set.
Fig. 2-15 TAMSIO/TSIOAM Instruction Execution Timing
SCK
SIO
TAMSIO
TSIOAM
Wait (6 Machine Cycle)
Instruction Execution
Machine Cycle
When the external clock (SCK input) is selected, the interface inputs serial clock pulses from the SCK input. When
an external serial clock pulse is input eight times, the INT0/S RQF is set and the termination of one-byte transfer
can be recognized. However, the eight serial clocks to be input must be counted on the side of the external clock
source because serial clock disable control is not performed internally. The transfer speed is determined by the
external serial clock within the range from DC to the maximum value limited by the standard.
When the external clock is used, the SIO, TAMSIO, or TSIOAM instruction the execution must be executed while
the serial clock pulse SCK is high. If such an instruction is executed while the SCK is rising or falling or is low, the
function of the instruction is not guaranteed.
相關PDF資料
PDF描述
UPD7554A 4-BIT SINGLE-CHIP MICROCOMPUTER
UPD7554AA 4-BIT SINGLE-CHIP MICROCOMPUTER
UPD7554ACS 4-BIT SINGLE-CHIP MICROCOMPUTER
UPD7554AG 4-BIT SINGLE-CHIP MICROCOMPUTER
UPD75CG08E 4 BIT SINGLE CHIP CMOS MICROCOMPUTERS
相關代理商/技術參數
參數描述
UPD7566CS044 制造商:Panasonic Industrial Company 功能描述:IC
UPD75P0016CU 制造商:Renesas Electronics Corporation 功能描述:MCU 4-Bit 75XL CISC 16KB EPROM 2.5V/3.3V/5V 42-Pin SPDIP
UPD75P0016CU-A 制造商:Renesas Electronics Corporation 功能描述:MCU 4-Bit 75XL CISC 16KB EPROM 2.5V/3.3V/5V 42-Pin SPDIP 制造商:Renesas Electronics 功能描述:75XL 6MHz Cut Tape 制造商:Renesas 功能描述:MCU 4-Bit 75XL CISC 16KB EPROM 2.5V/3.3V/5V 42-Pin SPDIP
UPD75P0016GB-3BS-MTX 制造商:Renesas Electronics 功能描述:MCU 4-Bit 75XL CISC 16KB EPROM 2.5V/3.3V/5V 44-Pin PQFP
UPD75P0016GB-3BS-MTX-A 制造商:Renesas Electronics Corporation 功能描述:MCU 4-bit 75XL CISC 16KB EPROM 2.5V/3.3V/5V 44-Pin PQFP 制造商:Renesas 功能描述:MCU 4-bit 75XL CISC 16KB EPROM 2.5V/3.3V/5V 44-Pin PQFP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*