- 您現在的位置：買賣IC網 > PDF目錄373748 > TUSB3410VF BUS CONTROLLER PDF資料下載
參數資料
| 型號： | TUSB3410VF |
| 英文描述： | BUS CONTROLLER |
| 中文描述： | 總線控制器 |
| 文件頁數： | 17/92頁 |
| 文件大?。?/td> | 317K |
| 代理商： | TUSB3410VF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁
3
–
1
3 Detailed Controller Description
3.1
Operating Modes
The TUSB3410 controls its USB interface in response to USB commands, and this action remains the same
independent of the serial port mode selected. On the other hand, the serial port can be set up in three modes.
As with any interface device, data movement is the TUSB3410
’
s main function, but typically the initial configuration
and error handling consume most of the support code. The following sections describe the various modes the device
can be used in and the means of setting up the device.
3.2
USB Interface Configuration
The TUSB3410 contains onboard ROM microcode, which enables the MCU to enumerate the device as a USB
peripheral. The ROM microcode can also load application code into internal RAM from either external memory via
the I
2
C bus or from the host via the USB.
3.2.1
External Memory Case
After reset, the TUSB3410 is disconnected from the USB because the pullup resistor CONT bit is cleared. The
TUSB3410 checks the I
2
C port for the existence of valid code, if it finds valid code, it uploads the code from the
external memory device into the RAM program space. Once loaded, the TUSB3410 connects to the USB by setting
the CONT bit and enumeration and configuration are performed. This is the most likely use of the device.
3.2.2
Host Download Case
If the valid code is not found at the I
2
C port, the TUSB3410 connects to the USB by setting the CONT bit, and then
an enumeration and default configuration are performed. The host can then download additional microcode into RAM
to tailor the application. Then, the MCU causes a disconnect and reconnect by using the pullup resistor CONT bit
in the USBCTL register, which causes the TUSB3410 to be re-enumerated with a new configuration.
3.3
USB Data Movement
From the USB perspective, the TUSB3410 looks like a USB peripheral device. It uses endpoint 0 as its control
endpoint, as do all USB peripherals. It also configures up to three input and three output endpoints, although most
applications use one bulk input endpoint for data in, one bulk output endpoint for data out, and one interrupt endpoint
for status updates. The USB configuration likely remains the same regardless of the serial port configuration.
Most data is moved from the USB side to the UART side and vice versa using on-chip DMA transfers. Some special
cases may use programmed IO under control of the MCU.
3.4
Serial Port Setup
The serial port requires a few control registers to be written to configure its operation. This configuration likely remains
the same regardless of the data mode used. These registers include the line control register that controls the serial
word format and the divisor registers that control the baud rate.
These registers are usually controlled by the host application.
3.5
Serial Port Data Modes
The serial port can be configured in three different, although similar, data modes. Similar to the USB mode, once
configured for a specific application, it is unlikely that the mode would be changed. The different modes affect the
timing of the serial input and output or the use of the control signals. However, the basic serial-to-parallel conversion
相關PDF資料 |
PDF描述 |
|---|---|
| TV2050MK5 | TV_ICs: |
| TVGA9000 | LOW COST VGA CONTROLLER |
| TVP3020-200PCE | Video DAC with Color Palette (RAMDAC) |
| TVP3025-220PCE | Video DAC with Color Palette (RAMDAC) |
| TVR1B | TOSHIBA Fast Recovery Diode Silicon Diffused Type |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TUSB3410VFG4 | 功能描述:USB 接口集成電路 RS232/IrDA Ser-to-USB Converter RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| TUSB4020BIPHP | 功能描述:USB Hub Controller USB 2.0 USB Interface 48-HTQFP (7x7) 制造商:texas instruments 系列:- 包裝:管件 零件狀態:有效 協議:USB 功能:集線器控制器 接口:USB 標準:USB 2.0 電壓 - 電源:1.1V，3.3V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 封裝/外殼:48-TQFP 裸露焊盤 供應商器件封裝:48-HTQFP（7x7） 標準包裝:250 |
| TUSB4020BIPHPR | 功能描述:IC USB 2.0 2PORT HUB IND 48HTQFP 制造商:texas instruments 系列:- 包裝:剪切帶（CT） 零件狀態:在售 協議:USB 功能:集線器控制器 接口:USB 標準:USB 2.0 電壓 - 電源:1.1V，3.3V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 封裝/外殼:48-TQFP 裸露焊盤 供應商器件封裝:48-HTQFP（7x7） 標準包裝:1 |
| TUSB4020BIPHPRQ1 | 功能描述:USB Hub Controller USB 2.0 USB Interface 48-HTQFP (7x7) 制造商:texas instruments 系列:- 包裝:剪切帶（CT） 零件狀態:有效 協議:USB 功能:集線器控制器 接口:USB 標準:USB 2.0 電壓 - 電源:1.1V，3.3V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 封裝/外殼:48-TQFP 裸露焊盤 供應商器件封裝:48-HTQFP（7x7） 標準包裝:1 |
| TUSB4020BPHPEVM | 功能描述:TUSB4020B - Interface, USB 2.0 Hub Evaluation Board 制造商:texas instruments 系列:- 零件狀態:有效 主要用途:接口，USB 2.0 集線器 嵌入式:- 使用的 IC/零件:TUSB4020B 主要屬性:2 通道（雙路） 輔助屬性:LED 狀態指示器 所含物品:板 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。