- 您現在的位置：買賣IC網 > PDF目錄231083 > TPS40180RGER (TEXAS INSTRUMENTS INC) 0.05 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC24 PDF資料下載
參數資料
| 型號： | TPS40180RGER |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 0.05 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC24 |
| 封裝： | GREEN, PLASTIC, VQFN-24 |
| 文件頁數： | 19/52頁 |
| 文件大?。?/td> | 1291K |
| 代理商： | TPS40180RGER |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
www.ti.com
SLVS753B – FEBRUARY 2007 – REVISED NOVEMBER 2007
Table 2. RT Voltage and Clock Master/Slave
RT VOLTAGE (VRT) (V)
CLOCK MODE
< 0.5
Master (or single converter)
> 2 (tied to PVCC or VDD)
Slave
In the clock master mode, the master clock frequency is set by connecting a resistor from the RT pin to GND. In
the clock master mode, the PSEL pin selects the CLKIO operating mode for the device. There are three possible
states defined in Table 3.
Table 3. PSEL Pin Modes for Clock Master
PSEL RESISTANCE to GND
MODE
(k
)
0
No CLKIO. CLKIO does not send out pulses.
OPEN
8 phase CLKIO. CLKIO send out a pulse train for interleaving with 45
° phase separation
29.4
6 phase CLKIO. CLKIO send out a pulse train for interleaving with 60
° phase separation
In the clock slave mode, the CLKIO pin is an input. The controller fires in a fixed relationship to the master
determined by the resistance placed from PSEL to GND, or is turned off to improve efficiency at light load. The
actual result depends on how the master CLKIO is programmed.
Table 4. PSEL Phase Programming for Slave With 8
Phase Master Clock
PHASE ANGLE (
°)
PSEL RESISTANCE to GND (k
)
Standby
OPEN
45
0
90
14.7
135
29.4
180
47
225
68
270
95.3
315
127
Table 5. PSEL Phase Programming for Slave With 6
Phase Master Clock
PHASE ANGLE (
°)
PSEL RESISTANCE to GND (k
)
Standby
OPEN
0
95.3
60
0
120
14.7
180
29.4
240
47
300
68
When a slave senses any level change on the PSEL pin that would indicate a change in firing angle, it
momentarily goes into standby mode. When a slave leaves standby mode, it starts supplying current after 64
clock cycles have elapsed if the status of the PSEL pin has not changed from when the device entered standby
mode. In this way, a slave can have its firing angle dynamically changed depending on operating conditions. A
slave can be held in standby mode by allowing the PSEL pin to float.
26
Copyright 2007, Texas Instruments Incorporated
Product Folder Link(s): TPS40180
相關PDF資料 |
PDF描述 |
|---|---|
| TPS2321IDG4 | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
| TK11819MTL | SWITCHING REGULATOR, PDSO6 |
| TH74KA22BVWORPGD/T | SPECIALTY ANALOG CIRCUIT, CQCC84 |
| TH7422BVWONGS | SPECIALTY ANALOG CIRCUIT, CQCC84 |
| TC520ACOE713 | SPECIALTY ANALOG CIRCUIT, PDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS40180RGERG4 | 功能描述:DC/DC 開關控制器 Single Ph Stackable Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TPS40180RGET | 功能描述:DC/DC 開關控制器 Single Ph Stackable Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TPS40180RGETG4 | 功能描述:DC/DC 開關控制器 Sgl Phase Stackable Cntrlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TPS40190 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:LOW PIN COUNT SYNCHRONOUS BUCK CONTROLLER |
| TPS40190DRC | 制造商:Texas Instruments 功能描述:DC/DC CONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。