參數資料
型號： TPS40180RGER
廠商： TEXAS INSTRUMENTS INC
元件分類： 穩壓器
英文描述： 0.05 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC24
封裝： GREEN, PLASTIC, VQFN-24
文件頁數： 14/52頁
文件大?。?/td> 1291K
代理商： TPS40180RGER
www.ti.com
Hiccup Fault Recovery
SS
SW NODE
VOUT
COMP
ILIM
V
VDD
1.5 V
0.5 V
GND
VIN
GND
VOUT, REG
GND
t0 t1 t2
t3
(A)
(B)
(C)
(D)
UDG-07024
SLVS753B – FEBRUARY 2007 – REVISED NOVEMBER 2007
To reduce the input current and component dissipation during on overcurrent event, a hiccup mode is
implemented. Hiccup mode refers to a sequence of 7 soft-start cycles where no MOSFET switching occurs, and
then a re-start is attempted. If the fault has cleared, the re-start results in returning to normal operation and
regulation. This is shown in Figure 26.
Figure 26. Hiccup Recovery From Faults
Normal operation is occurring between t0 and t1 as shown by VOUT at the regulated voltage, (C) and normal
switching on the SW NODE (B) and COMP at its nominal level, (D). At t1, an overcurrent load is experienced.
The increased current forces COMP to increase to the ILIM level as shown in (D). If the COMP voltage is above
the ILIM voltage for 7 switching cycles, the controller enters a hiccup mode at t2. During this time the controller is
not switching and the power MOSFETs are turned off. The SS pin goes through 7 cycles of charging and
discharging the soft-start capacitor. At the end of the 7 cycles the controller attempts another normal re-start. If
the fault has been cleared, the output voltage comes up to the regulation level as shown at time t3. If the fault
has not cleared, the COMP voltage again rises above the ILIM voltage and a fresh hiccup cycle starts. This
condition may continue indefinitely.
The pre-bias circuitry is reset at this time and the restart does not discharge an output pre-bias condition if it
exists.
Copyright 2007, Texas Instruments Incorporated
21
Product Folder Link(s): TPS40180
相關PDF資料
PDF描述
TPS2321IDG4 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16
TK11819MTL SWITCHING REGULATOR, PDSO6
TH74KA22BVWORPGD/T SPECIALTY ANALOG CIRCUIT, CQCC84
TH7422BVWONGS SPECIALTY ANALOG CIRCUIT, CQCC84
TC520ACOE713 SPECIALTY ANALOG CIRCUIT, PDSO16
相關代理商/技術參數
參數描述
TPS40180RGERG4 功能描述:DC/DC 開關控制器 Single Ph Stackable Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
TPS40180RGET 功能描述:DC/DC 開關控制器 Single Ph Stackable Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
TPS40180RGETG4 功能描述:DC/DC 開關控制器 Sgl Phase Stackable Cntrlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
TPS40190 制造商:TI 制造商全稱:Texas Instruments 功能描述:LOW PIN COUNT SYNCHRONOUS BUCK CONTROLLER
TPS40190DRC 制造商:Texas Instruments 功能描述:DC/DC CONTROLLER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*