參數資料
型號： TMP320LC2401APZS
廠商： Texas Instruments, Inc.
元件分類： 數字信號處理
英文描述： DSP CONTROLLERS
中文描述： DSP控制器
文件頁數： 57/134頁
文件大小： 1759K
代理商： TMP320LC2401APZS
TMS320LF2407A,TMS320LF2406A,TMS320LF2403A,TMS320LF2402A
TMS320LC2406A,TMS320LC2404A,TMS320LC2403A,TMS320LC2402A
DSP CONTROLLERS
SPRS145K
JULY 2000
REVISED AUGUST 2005
57
POST OFFICE BOX 1443
HOUSTON, TEXAS 77251
1443
SPI slave mode operation in LF2403A
The LF2403A device does not have the SPISTE/IOPC5 pin. (This function is available as an internal signal only.)
The following must be done to put the LF2403A SPI in slave mode:
1.
Configure SPISTE/IOPC5 signal for GPIO mode by clearing the MCRB.5 bit.
2.
Configure SPISTE/IOPC5 signal as an output (by writing a 1 to bit 13 of PCDATDIR) and drive it low (by
writing a 0 to bit 5 of PCDATDIR). Note that SPISTE/IOPC5 should not be driven low until after the SPI is
configured and taken out of reset.
NOTE: The slave SPISTE/IOPC5 signal must not be driven low until after the master
and
slave SPI modules
are configured and taken out of reset. The initialization sequence is as follows:
a.
The master SPI is configured first and taken out of reset. This ensures that the master SPICLK is
initialized to its appropriate level (high or low, depending on the polarity bit) first, before the slave SPI
starts accepting clock pulses.
b.
The slave SPI is configured and taken out of reset.
c.
The GPIO/SPI pins of the slave is then configured for SPI operation and the SPISTE/IOPC5 signal is
driven low. This is done
after
ensuring the correct level of the master SPICLK signal. One method of
doing this would be to read the level of the SPICLK pin through the PCDATDIR register and then
deciding on the appropriate course of action.
d.
SPI transmission may commence now. Transmission of data should not be attempted until both master
and slave are configured and the slave SPISTE/IOPC5 signal is driven low.
PLL-based clock module
The 240xA has an on-chip, PLL-based clock module. This module provides all the necessary clocking signals
for the device, as well as control for low-power mode entry. The PLL has a 3-bit ratio control to select different
CPU clock rates. See Figure 16 for the PLL Clock Module Block Diagram, Table 9 for clock rates, and Table 10
for the loop filter component values.
The PLL-based clock module provides two modes of operation:
Crystal-operation
This mode allows the use of an external crystal/resonator to provide the time base to the device.
External clock source operation
This mode allows the internal oscillator to be bypassed. The device clocks are generated from an external
clock source input on the XTAL1/CLKIN pin. In this case, an external oscillator clock is connected to the
XTAL1/CLKIN pin.
相關PDF資料
PDF描述
5082-7661-CG400 7.6 mm (0.3 inch)/10.9 mm (0.43 inch) Seven Segment Displays
74ACT823LMQB 9-Bit D Flip-Flop
50E-2C-38.0 TRANS PREBIASED PNP 200MW SOT23
500E-3CL-5.5 E Rated Medium Voltage Fuses
500E-3C-5.5 E Rated Medium Voltage Fuses
相關代理商/技術參數
參數描述
TMP320LC2401AVFA 制造商:TI 制造商全稱:Texas Instruments 功能描述:DSP CONTROLLERS
TMP320LC2401AVFS 制造商:TI 制造商全稱:Texas Instruments 功能描述:DSP CONTROLLERS
TMP320LC2402APAGA 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DSP|16-BIT|CMOS|TQFP|64PIN|PLASTIC
TMP320LC2402APAGS 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DSP|16-BIT|CMOS|TQFP|64PIN|PLASTIC
TMP320LC2402APGA 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DSP|16-BIT|CMOS|QFP|64PIN|PLASTIC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*