參數資料
型號： TDA8031HL
廠商： NXP SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： USB smart card reader (OTP or ROM)
中文描述： SPECIALTY MICROPROCESSOR CIRCUIT, PQFP64
封裝： 10 X 10 MM, 1.40 MM HEIGHT, MS-026, SOT-314-2, LQFP-64
文件頁數： 43/57頁
文件大?。?/td> 228K
代理商： TDA8031HL
2003 Jul 04
43
Philips Semiconductors
Product specification
USB smart card reader (OTP or ROM)
TDA8030; TDA8031
Table 45
Description of the Power-on value for Set end-point status bits
Table 46
Data buffer organization (read)
Notes
1.
Bit 7 of Byte 0 indicates whether the packet in the buffer was received successfully over the USB-bus. When this bit
is set to logic 1, the packet was received successfully.
Bit 6 of Byte 0 indicates whether the packet in the buffer is a set-up packet.
2.
Table 47
Data buffer organization (write)
Table 48
Power-on value for Clear buffer
FUNCTION
DESCRIPTION
Stall
Disable
If set to logic 1, the end-point is stalled.
If set to logic 1, the end-point is disabled. After a bus reset; each end-point is enabled, i.e. this
bit is set to logic 0.
If set to logic 0, the interrupt end-point is in toggle mode. If set to logic 1, the interrupt end-point
is in rate feedback mode.
If set to logic 1, an event on the end-point causes an interrupt to the microcontroller.
If set to logic 1, both end-points zero are stalled; unless the set-up packet bit is set.
A stalled control end-point is automatically unstalled when it receives a SET-UP token,
regardless of the content of the packet. If the end-point stays in the stalled state, the
microcontroller should re-install it.
When a stalled end-point is unstalled (either by the Set end-point status command or by
receiving a Set-up token) it is also re-initialized. This flushes the buffer: in case of an output
buffer, it waits for a DATA 0 PID; in case of an input buffer, it writes a DATA 0 PID. Even when
unstalled, setting the stalled bit to logic 0 initializes the end-point.
When an end-point is stalled by the Set end-point status command, it is also re-initialized.
Rate feedback
mode
Interrupt unmasked
Conditional stall
BYTE
7
(1)
6
(2)
5
4
3
2
1
0
Byte 0
Byte 1
Byte 2
....
Byte n + 1
0/1
0/1
0
number of data bytes in buffer
data byte 0
data byte n
1
BYTE
7
6
5
4
3
2
1
0
Byte 0
Byte 1
Byte 2
....
Byte n + 1
0
number of data bytes in buffer
data byte 0
data byte n
1
FUNCTION
7
6
5
4
3
2
1
0
Packet overwritten
Reserved
0
相關PDF資料
PDF描述
TDA8302 SMALL SIGNAL COMBINATION IC FOR COLOUR TV
TDA8931 Power comparator 1 X 20 W
TDA8931T Power comparator 1 X 20 W
TEA1201TS 0.95 V starting basic power unit
TEA5768HL Low-power FM stereo radio for handheld applications
相關代理商/技術參數
參數描述
TDA8034AT 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Smart card interface
TDA8034AT/C1 制造商:NXP Semiconductors 功能描述:Cut Tape
TDA8034AT/C1,112 功能描述:接口 - 專用 SMART CARD INTERFACE RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
TDA8034AT/C1,118 功能描述:接口 - 專用 SMART CARD INTERFACE RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
TDA8034HN/C1,118 功能描述:接口 - 專用 SMART CARD INTERFACE RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*