- 您現在的位置：買賣IC網 > PDF目錄382581 > TDA8031HL (NXP SEMICONDUCTORS) USB smart card reader (OTP or ROM) PDF資料下載
參數資料
| 型號： | TDA8031HL |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | USB smart card reader (OTP or ROM) |
| 中文描述： | SPECIALTY MICROPROCESSOR CIRCUIT, PQFP64 |
| 封裝： | 10 X 10 MM, 1.40 MM HEIGHT, MS-026, SOT-314-2, LQFP-64 |
| 文件頁數： | 17/57頁 |
| 文件大?。?/td> | 228K |
| 代理商： | TDA8031HL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
2003 Jul 04
17
Philips Semiconductors
Product specification
USB smart card reader (OTP or ROM)
TDA8030; TDA8031
Table 8
Time-out counter configuration
TOC VALUE
OPERATING MODE
00H
05H
61H
All counters are stopped.
Counters 2 and 3 are stopped; counter 1 continues to operate in autoreload mode.
Counter 1 is stopped and counters 3 and 2 form a 16-bit counter. Counting the value stored in TOR3
and TOR2 is started after 6H is written in the TOCR. An interrupt is given and bit TO3 is set within the
USR when the terminal count is reached. The counter is stopped by writing 00H in the TOCR and will
be stopped before reloading a new value in TOR2 and TOR3.
Counter 1 is an 8-bit autoreload counter and counters 3 and 2 form a 16-bit counter. Counter 1 starts
counting the content of TOR1 on the first START bit (reception or transmission) detected on I/O after
65H is written in the TOCR. When Counter 1 reaches its terminal count, an interrupt is given, bit TO1 in
the USR is set and the counter automatically restarts the same count until it is stopped. It is not allowed
to change the content of TOR1 during a count. Counters 3 and 2 are wired as a single 16-bit counter
and starts counting the value TOR3 and TOR2 when 65H is written in the TOCR. When the counter
reaches its terminal count, an interrupt is given and bit TO3 is set within the USR. Both counters are
stopped when 00H is written in the TOCR. Counters 3 and 2 will be stopped by writing 05H in the
TOCR before reloading a new value in TOR2 and TOR3.
Counters 3, 2 and 1 are wired as a single 24-bit counter. Counting the value stored in TOR3,
TOR2 and TOR1 is started after 68H is written in the TOCR. The counter is stopped by writing 00H in
the TOCR. It is not allowed to change the content of TOR3, TOR2 and TOR1 within a count.
Counters 3, 2 and 1 are wired as a single 24-bit counter. Counting the value stored in TOR3,
TOR2 and TOR1 on the first start bit detected on I/O (reception or transmission) after the value has
been written. It is possible to change the content of TOR3, TOR2 and TOR1 during a count; the current
count will not be affected and the new count value will be taken into account at the next start bit. The
counter is stopped by writing 00H in the TOCR. In this configuration TOR3, TOR2 and TOR1 must not
be all zero.
Same as 05H, except that all the counters will be stopped at the end of the 12th ETU following the first
received start bit detected after 85H has been written in the TOCR.
Same configuration as TOCR = 65H, except that Counter 1 will be stopped at the end of the 12th ETU
following the first start bit detected after E5H has been written in the TOCR.
65H
68H
7CH
85H
E5H
Thetime-outcounterisveryusefulforprocessingtheclock
countingduringATR,theWorkWaitingTime(WWT)orthe
waiting times defined in T = 1 protocol. The 200 and
384 clock counter used during ATR is done by hardware
when Start Session is set, a specific hardware takes care
of BGT in T = 1 protocol and a specific register is present
for processing the extra guard time.
It is not allowed to change the content of the TOR registers
whilst a counter is in software triggered mode, or in
autoreload mode. In these modes, it is mandatory to stop
the counters (TOCR = 00H or 05H) before updating the
count value in the TOR registers. In start bit triggered
mode, the value may be changed at any time; the new
count value will be taken into account on the next start bit.
The minimum time interval between 2 successive write
operations in TOCR is
2
31
or
2
32
ETU.
It is obvious that the counters may only be used once the
card has been activated.
Detailed examples of how to use these specific timers can
be found in Application Note “AN01012”
相關PDF資料 |
PDF描述 |
|---|---|
| TDA8302 | SMALL SIGNAL COMBINATION IC FOR COLOUR TV |
| TDA8931 | Power comparator 1 X 20 W |
| TDA8931T | Power comparator 1 X 20 W |
| TEA1201TS | 0.95 V starting basic power unit |
| TEA5768HL | Low-power FM stereo radio for handheld applications |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA8034AT | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Smart card interface |
| TDA8034AT/C1 | 制造商:NXP Semiconductors 功能描述:Cut Tape |
| TDA8034AT/C1,112 | 功能描述:接口 - 專用 SMART CARD INTERFACE RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| TDA8034AT/C1,118 | 功能描述:接口 - 專用 SMART CARD INTERFACE RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| TDA8034HN/C1,118 | 功能描述:接口 - 專用 SMART CARD INTERFACE RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
發布緊急采購，3分鐘左右您將得到回復。