- 您現在的位置：買賣IC網 > PDF目錄382581 > TDA8031HL (NXP SEMICONDUCTORS) USB smart card reader (OTP or ROM) PDF資料下載
參數資料
| 型號： | TDA8031HL |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | USB smart card reader (OTP or ROM) |
| 中文描述： | SPECIALTY MICROPROCESSOR CIRCUIT, PQFP64 |
| 封裝： | 10 X 10 MM, 1.40 MM HEIGHT, MS-026, SOT-314-2, LQFP-64 |
| 文件頁數： | 15/57頁 |
| 文件大?。?/td> | 228K |
| 代理商： | TDA8031HL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
2003 Jul 04
15
Philips Semiconductors
Product specification
USB smart card reader (OTP or ROM)
TDA8030; TDA8031
8.1.3.2
Hardware status register
The Hardware Status Register (HSR) gives the status of the chip after a hardware problem has been detected.
Table 2
Hardware Status Register (address 0FH; read only); note 1
Note
1.
All bits are cleared after reset.
Table 3
Description of the HSR bits
When either bits PRTL, PRL or PTL is logic 1, then pin INT0 is LOW. The bits having caused the interrupt are cleared
when the HSR has been readout (2
×
f
int
cycles after the rising edge of RD).
At power-on, or after a supply voltage drop-out, SUPL is set and INT0 is LOW. INT0 will return HIGH at the end of the
internal Power-on reset pulse defined by the value of the capacitor connected to pin CDELAY. SUPL will be reset only
after a status register readout outside the Power-on reset pulse; see Fig.8.
In the event of emergency deactivation (by PRTL, SUPL, PRL and PTL), bit START will be automatically reset by
hardware.
8.1.3.3
Time-out registers
The three Time-Out Registers TOR1, TOR2 and TOR3 form a programmable 24-bit ETU counter, or two independant
counters (one 16-bit and one 8-bit).
The value to load in TOR1, TOR2 and TOR3 is the number of ETUs to count.
Table 4
Time-out register 1 (address 09H; write only); note 1
Note
1.
All bits are cleared after reset.
7
6
5
4
3
2
1
0
PRTL
SUPL
PRL
PTL
BIT
SYMBOL
PRTL
DESCRIPTION
7 and 6
5
not used
Protection 1: Bit PRTL = 1 when a default has been detected on card reader. Bit PRTL
is the OR function of the protection on pins V
CC
and RST.
Supervisor Latch: Bit SUPL = 1 when the supervisor has been activated.
not used
Presence Latch: Bit PRL = 1 when a change has occurred on pin PRES.
not used
Overheating: Bit PTL = 1 if overheating has occurred.
4
3
2
1
0
SUPL
PRL
PTL
7
6
5
4
3
2
1
0
TOL7
TOL6
TOL5
TOL4
TOL3
TOL2
TOL1
TOL0
相關PDF資料 |
PDF描述 |
|---|---|
| TDA8302 | SMALL SIGNAL COMBINATION IC FOR COLOUR TV |
| TDA8931 | Power comparator 1 X 20 W |
| TDA8931T | Power comparator 1 X 20 W |
| TEA1201TS | 0.95 V starting basic power unit |
| TEA5768HL | Low-power FM stereo radio for handheld applications |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA8034AT | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Smart card interface |
| TDA8034AT/C1 | 制造商:NXP Semiconductors 功能描述:Cut Tape |
| TDA8034AT/C1,112 | 功能描述:接口 - 專用 SMART CARD INTERFACE RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| TDA8034AT/C1,118 | 功能描述:接口 - 專用 SMART CARD INTERFACE RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| TDA8034HN/C1,118 | 功能描述:接口 - 專用 SMART CARD INTERFACE RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
發布緊急采購，3分鐘左右您將得到回復。