- 您現在的位置：買賣IC網 > PDF目錄382581 > TDA8031HL (NXP SEMICONDUCTORS) USB smart card reader (OTP or ROM) PDF資料下載
參數資料
| 型號： | TDA8031HL |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | USB smart card reader (OTP or ROM) |
| 中文描述： | SPECIALTY MICROPROCESSOR CIRCUIT, PQFP64 |
| 封裝： | 10 X 10 MM, 1.40 MM HEIGHT, MS-026, SOT-314-2, LQFP-64 |
| 文件頁數： | 38/57頁 |
| 文件大?。?/td> | 228K |
| 代理商： | TDA8031HL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁當前第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
2003 Jul 04
38
Philips Semiconductors
Product specification
USB smart card reader (OTP or ROM)
TDA8030; TDA8031
Table 32
Device commands
Table 33
Power-on value for Set address
Notes
1.
2.
The value written becomes the address.
A logic 1 enables the function.
After a bus reset, the address is reset to 000 0000. The enable bit is set. The device will respond on packets for function
address 000 0000, end-point 0 (default end-point).
COMMAND
DESCRIPTION
Set address
The set address command is used to set the USB assigned address and to enable the function. In
the event that the status phase of the set address transaction is not successful, the device address
will not be updated. The power-on value is given in Table 33.
A value of 1 written to the register indicates that the non-control end-points are enabled. The
power-on value is given in Table 34.
The default value is logic 0; if logic 1 is written in this register, then NAKing is reported and will
generate an interrupt. When set to logic 0, only successful transactions are reported.
This command indicates the origin of an interrupt. The end-point interrupt bits are cleared by the
Select end-point/Clear Interrupt command. The power-on value is given in Table 35.
The Read Current Frame Number returns the frame number of the last received Start Of Frame
(SOF). The frame number is eleven bits wide. The frame number is returned LSB first, so, if the
user is only interested in the lower 8 bits of the frame number, only the first byte needs to be read;
see Table 36.
The frame number returned by this commend can be invalid in the event of one of the following
conditions:
If no SOF was received by the device at the beginning of a frame, the frame number returned is
that of the last successfully received SOF
If the SOF frame number contained a CRC error, the frame number received will be the corrupted
frame number as received by the device.
The chip Identification is 16 bits wide. The command divides the ID into bytes and returns the least
significant byte first: For the TDA8030; TDA8031, the ID is fixed at 2B00H.
The Get Device Status command returns the Device Status Register; refer to the Set Device Status
command
The Set Device Status command sets bits in the Device Status Register.
In Table 37, the Type column indicates if the bit can be written and if the bit is cleared after reading
the register. The Interrupt column indicates if the bit generates an interrupt when it is set.
The Get Error Code command returns the error code of the last generated error; this command is
for debugging purpose. The 4 least significant bits form the error code. Bit 4 (Error Occurred) can
be cleared by each new transfer. The power-on value is given in Table 39.
This command is only useful during debugging.
Table 40 gives an overview of the Error Codes.
Set end-points
enable
Set Mode
Read interrupt
register
Read Current
Frame Number
Read chip ID
Get Device
Status
Set Device
Status
Debug
command: Get
Error Code
FUNCTION
7
6
5
4
3
2
1
0
Device
address
(1)
Enable
(2)
0
0
0
0
0
0
0
0
相關PDF資料 |
PDF描述 |
|---|---|
| TDA8302 | SMALL SIGNAL COMBINATION IC FOR COLOUR TV |
| TDA8931 | Power comparator 1 X 20 W |
| TDA8931T | Power comparator 1 X 20 W |
| TEA1201TS | 0.95 V starting basic power unit |
| TEA5768HL | Low-power FM stereo radio for handheld applications |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA8034AT | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Smart card interface |
| TDA8034AT/C1 | 制造商:NXP Semiconductors 功能描述:Cut Tape |
| TDA8034AT/C1,112 | 功能描述:接口 - 專用 SMART CARD INTERFACE RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| TDA8034AT/C1,118 | 功能描述:接口 - 專用 SMART CARD INTERFACE RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| TDA8034HN/C1,118 | 功能描述:接口 - 專用 SMART CARD INTERFACE RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
發布緊急采購，3分鐘左右您將得到回復。