- 您現在的位置：買賣IC網 > PDF目錄382581 > TDA8031HL (NXP SEMICONDUCTORS) USB smart card reader (OTP or ROM) PDF資料下載
參數資料
| 型號： | TDA8031HL |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | USB smart card reader (OTP or ROM) |
| 中文描述： | SPECIALTY MICROPROCESSOR CIRCUIT, PQFP64 |
| 封裝： | 10 X 10 MM, 1.40 MM HEIGHT, MS-026, SOT-314-2, LQFP-64 |
| 文件頁數： | 40/57頁 |
| 文件大?。?/td> | 228K |
| 代理商： | TDA8031HL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
2003 Jul 04
40
Philips Semiconductors
Product specification
USB smart card reader (OTP or ROM)
TDA8030; TDA8031
Table 38
Set device status command function bits
Table 39
Power-on value for Get Error Code
Table 40
Error codes
FUNCTION
DESCRIPTION
Suspend
The Suspend bit represents the current Suspend state. It is logic 1 when the device has not seen
any activity on its upstream port for more than 3 ms. It is reset to logic 0 on any activity.
When the device is suspended, (Suspend bit = 1) and the microcontroller writes logic 0 into it,
the device will generate a remote wake-up. When the device is not suspended, writing a logic 0
has no effect. Writing a logic 1 in this register has no an effect.
The Suspend Change bit is set to logic 1 when the Suspend bit toggles. The Suspend bit can
toggle because:
The device goes into the suspended state
The device receives resume signalling on its upstream port
The Suspend Change bit is reset after the register has been read.
The Bus reset bit is set when the device receives a bus reset. It is cleared when read. On a bus
reset, the device will automatically go to the default state (unconfigured and responding to
address 0).
Suspend Change
Bus reset
FUNCTION
7
6
5
4
0
3
2
1
0
Error code
Error occurred
Reserved
0
0
0
0
ERROR CODE[3:0]
DESCRIPTION
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
no error
PID encoding error
unknown PID
unexpected packet
error in token CRC
error in data CRC
time-out error
babble
error in end of packet
sent NAK
sent Stall
buffer overrun error
reserved
bitstuff error
error in sync
wrong toggle bit in data PID; ignored data
相關PDF資料 |
PDF描述 |
|---|---|
| TDA8302 | SMALL SIGNAL COMBINATION IC FOR COLOUR TV |
| TDA8931 | Power comparator 1 X 20 W |
| TDA8931T | Power comparator 1 X 20 W |
| TEA1201TS | 0.95 V starting basic power unit |
| TEA5768HL | Low-power FM stereo radio for handheld applications |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA8034AT | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Smart card interface |
| TDA8034AT/C1 | 制造商:NXP Semiconductors 功能描述:Cut Tape |
| TDA8034AT/C1,112 | 功能描述:接口 - 專用 SMART CARD INTERFACE RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| TDA8034AT/C1,118 | 功能描述:接口 - 專用 SMART CARD INTERFACE RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| TDA8034HN/C1,118 | 功能描述:接口 - 專用 SMART CARD INTERFACE RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
發布緊急采購，3分鐘左右您將得到回復。