參數資料
型號： TDA8031HL
廠商： NXP SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： USB smart card reader (OTP or ROM)
中文描述： SPECIALTY MICROPROCESSOR CIRCUIT, PQFP64
封裝： 10 X 10 MM, 1.40 MM HEIGHT, MS-026, SOT-314-2, LQFP-64
文件頁數： 25/57頁
文件大?。?/td> 228K
代理商： TDA8031HL
2003 Jul 04
25
Philips Semiconductors
Product specification
USB smart card reader (OTP or ROM)
TDA8030; TDA8031
Table 22
Description of the UCR1 bits
8.1.5.6
Clock configuration register
The Clock Configuration Register (CCR) defines the clock to the card and the clock to the ISO UART. If bit CKU in the
Prescaler Register (UCR2) of the card is set, then the ISO UART is clocked at twice the frequency to the card, this allows
higher baud rates to be reached than foreseen in the ISO7816 norm.
Table 23
Clock configuration register (address 01H; read and write); note 1
Note
1.
All bits are cleared after reset.
BIT
SYMBOL
FIP
DESCRIPTION
7
6
not used
Force Inverse Parity: If FIP = 1, then the UART will NAK a correct received character
and will transmit characters with wrong parity bit.
Bit FC is a test bit and must be left at logic 0.
Protocol: Bit PROT = 1 if the protocol type is asynchronous T = 1. If PROT = 0, the
protocol is T = 0.
Transmit/Receive: Bit T/R is set by software for transmission mode. A change from
0 to 1 will set bit TBE in the USR. T/R is automatically reset by hardware if LCT has
been used before transmitting the last character.
Last Character to Transmit: Bit LCT is set by software before writing the last character
to transmit into the UTR. It allows automatic change to reception mode when reset by
hardware at the end of a successful transmission (11 +
28
31
or
28
32
ETU in T = 0 and
10 +
28
31
or
28
32
ETU in T = 1). When LCT is being reset, the bit T/R is also reset and
the UART is then ready for receiving a character.
Start Session: Bit SS is set by software before ATR for automatic convention detection
and early answer detection. It is automatically reset by hardware at 10.5 ETU after
reception of the initial character.
Convention: Bit CONV = 1 if the convention is direct. CONV is either automatically
written to by hardware, according to the convention detected during ATR, or by software
if bit AUTOCONV is set.
5
4
FC
PROT
3
T/R
2
LCT
1
SS
0
CONV
7
6
5
4
3
2
1
0
SHL
CST
SC
AC2
AC1
AC0
相關PDF資料
PDF描述
TDA8302 SMALL SIGNAL COMBINATION IC FOR COLOUR TV
TDA8931 Power comparator 1 X 20 W
TDA8931T Power comparator 1 X 20 W
TEA1201TS 0.95 V starting basic power unit
TEA5768HL Low-power FM stereo radio for handheld applications
相關代理商/技術參數
參數描述
TDA8034AT 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Smart card interface
TDA8034AT/C1 制造商:NXP Semiconductors 功能描述:Cut Tape
TDA8034AT/C1,112 功能描述:接口 - 專用 SMART CARD INTERFACE RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
TDA8034AT/C1,118 功能描述:接口 - 專用 SMART CARD INTERFACE RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
TDA8034HN/C1,118 功能描述:接口 - 專用 SMART CARD INTERFACE RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*