參數資料
型號： ST72774S9T1/XXX
廠商： STMICROELECTRONICS
元件分類： 微控制器/微處理器
英文描述： 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP44
封裝： TQFP-44
文件頁數： 128/144頁
文件大?。?/td> 1280K
代理商： ST72774S9T1/XXX
ST72774/ST727754/ST72734
84/144
USB INTERFACE (Cont’d)
ENDPOINT n REGISTER B (EPnRB)
Read / Write
Reset Value: 0000 xxxx (0xh)
These registers (EP1RB and EP2RB) are used for
controlling data reception on Endpoints 1 and 2.
They are also reset by the USB bus reset.
Note: Endpoint 2 and the EP2RB register are not availa-
ble on some devices (see device feature list and
register map).
Bit 7 = CTRL
Control.
This bit should be 0.
Note: If this bit is 1, the Endpoint is a control endpoint.
(Endpoint 0 is always a control Endpoint, but it is
possible to have more than one control Endpoint).
Bit 6 = DTOG_RX
Data toggle, for reception
transfers.
It contains the expected value of the toggle bit
(0=DATA0, 1=DATA1) for the next data packet.
This bit is cleared by hardware in the first stage
(Setup Stage) of a control transfer (SETUP
transactions start always with DATA0 PID). The
receiver toggles DTOG_RX only if it receives a
correct data packet and the packet’s data PID
matches the receiver sequence bit.
Bit 5:4 = STAT_RX [1:0]
Status bits, for reception
transfers.
These bits contain the information about the
endpoint status, which are listed in the following
table:
These bits are written by software. Hardware sets
the STAT_RX bits to NAK when a correct transfer
has occurred (CTR=1) related to an OUT or
SETUP transaction addressed to this endpoint, so
the software has the time to elaborate the received
data before acknowledging a new transaction.
Bits 3:0 = EA[3:0]
Endpoint address.
Software must write in this field the 4-bit address
used to identify the transactions directed to this
endpoint. Usually EP1RB contains “0001” and
EP2RB contains “0010”.
ENDPOINT 0 REGISTER B (EP0RB)
Read / Write
Reset Value: 1000 0000 (80h)
This register is used for controlling data reception
on Endpoint 0. It is also reset by the USB bus
reset.
Bit 7 = Forced by hardware to 1.
Bit 6:4 = Refer to the EPnRB register for a
description of these bits.
Bit 3:0 = Forced by hardware to 0.
70
CTRL
DTOG
_RX
STAT
_RX1
STAT
_RX0
EA3
EA2
EA1
EA0
STAT_RX1 STAT_RX0 Meaning
00
DISABLED: reception
transfers
cannot
be
executed.
01
STALL: the endpoint is
stalled and all reception
requests result in a STALL
handshake.
10
NAK: the endpoint is na-
ked and all reception re-
quests result in a NAK
handshake.
11
VALID: this endpoint is
enabled for reception.
70
1
DTOG
RX
STAT
RX1
STAT
RX0
00
0
相關PDF資料
PDF描述
ST72E734J6D0 8-BIT, UVPROM, 8 MHz, MICROCONTROLLER, CDIP42
ST72T774S9T1 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP44
ST7294C6B6 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PDIP28
ST72T94C6M6 8-BIT, OTPROM, MICROCONTROLLER, PDSO28
ST72C171K2B6 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDIP32
相關代理商/技術參數
參數描述
ST727X4-EMU2B 制造商:STMicroelectronics 功能描述:REALTIME EMULATOR BOARD - Bulk
ST727X4-EPB/US 制造商:STMicroelectronics 功能描述:PROGRAMMER - Bulk
ST-7-28 功能描述:XFRMR PWR 115V 14VAC 2.6A RoHS:是 類別:變壓器 >> 功率 系列:ST 標準包裝:1 系列:260 類型:標準 最大功率:65 VA 主線圈:雙 副線圈:三路，中心抽頭 在某電流時的串聯輸出電壓:500 VAC @ 85mA，5 VAC @ 2A，6.3 VAC @ 2A 在某電流時的并聯輸出電壓:- 安裝類型:底座安裝 尺寸/尺寸:102.36mm L x 67.31mm W 高度 - 座高（最大）:66.80mm 端接類型:導線引線
ST7-28 制造商:SUPERWORLD 制造商全稱:Superworld Electronics 功能描述:POWER TRANSFORMER
ST7-28B56 功能描述:電源變壓器 SPLIT BOBBIN HORZ MOUNT XFMR RoHS:否 制造商:Triad Magnetics 功率額定值:12 VA 初級電壓額定值:115 V / 230 V 次級電壓額定值:12 V / 24 V 安裝風格:SMD/SMT 一次繞組:Dual Primary Winding 二次繞組:Dual Secondary Winding 長度:2.5 in 寬度:2 in 高度:1.062 in
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*