參數資料
型號: ST72774S9T1/XXX
廠商: STMICROELECTRONICS
元件分類: 微控制器/微處理器
英文描述: 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP44
封裝: TQFP-44
文件頁數: 11/144頁
文件大?。?/td> 1280K
代理商: ST72774S9T1/XXX
ST72774/ST727754/ST72734
108/144
DDC INTERFACE (Cont’d)
Slave Receiver
Following the address reception and after SR1
register has been read, the slave receives bytes
from the SDA line into the DR register via the
internal shift register. After each byte, the following
events occur in sequence:
– Acknowledge pulse is generated if the ACK bit is
set.
– EVF and BTF bits are set.
– An interrupt is generated if the ITE bit is set.
Then the interface waits for a read of the SR1
register followed by a read of the DR register,
holding the SCL line low (see Figure 67 Transfer
sequencing EV2).
Slave Transmitter
Following the address reception and after SR1
register has been read, the slave sends bytes from
the DR register to the SDA line via the internal shift
register.
The slave waits for a read of the SR1 register
followed by a write in the DR register, holding the
SCL line low (see Figure 67 Transfer sequencing
EV3).
When the acknowledge pulse is received:
– EVF and BTF bits are set.
– An interrupt is generated if the ITE bit is set.
Closing slave communication
After the last data byte is transferred, a Stop
Condition is generated by the master. The
interface detects this condition and in this case:
– EVF and STOPF bits are set.
– An interrupt is generated if the ITE bit is set.
Then the interface waits for a read of the SR2
register (see Figure 67 Transfer sequencing EV4).
Error Cases
– BERR: Detection of a Stop or a Start condition
during a byte transfer. In this case, the EVF and
the BERR bits are set and an interrupt is gener-
ated if the ITE bit is set.
If it is a Stop then the interface discards the data,
releases the lines and waits for another Start
condition.
If it is a Start then the interface discards the data
and waits for the next slave address on the bus.
– AF: Detection of a non-acknowledge bit. In this
case, the EVF and AF bits are set and an inter-
rupt is generated if the ITE bit is set.
Note:In both cases, SCL line is not held low; however,
SDA line can remain low due to possible 0 bits
transmitted last. It is then necessary to release both
lines by software.
How to release the SDA / SCL lines
Set and subsequently clear the STOP bit while
BTF is set. The SDA/SCL lines are released after
the transfer of the current byte.
Other Events
s
ADSL: Detection of a Start condition after an
acknowledge time-slot.
The state machine is reset and starts a new
process. The ADSL bit is set and an interrupt is
generated if the ITE bit is set. The SCL line is
stretched low.
s
STOPF: Detection of a Stop condition after an
acknowledge time-slot.
The state machine is reset. Then the STOPF
flag is set and an interrupt is generated if the ITE
bit is set.
相關PDF資料
PDF描述
ST72E734J6D0 8-BIT, UVPROM, 8 MHz, MICROCONTROLLER, CDIP42
ST72T774S9T1 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP44
ST7294C6B6 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PDIP28
ST72T94C6M6 8-BIT, OTPROM, MICROCONTROLLER, PDSO28
ST72C171K2B6 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDIP32
相關代理商/技術參數
參數描述
ST727X4-EMU2B 制造商:STMicroelectronics 功能描述:REALTIME EMULATOR BOARD - Bulk
ST727X4-EPB/US 制造商:STMicroelectronics 功能描述:PROGRAMMER - Bulk
ST-7-28 功能描述:XFRMR PWR 115V 14VAC 2.6A RoHS:是 類別:變壓器 >> 功率 系列:ST 標準包裝:1 系列:260 類型:標準 最大功率:65 VA 主線圈:雙 副線圈:三路,中心抽頭 在某電流時的串聯輸出電壓:500 VAC @ 85mA,5 VAC @ 2A,6.3 VAC @ 2A 在某電流時的并聯輸出電壓:- 安裝類型:底座安裝 尺寸/尺寸:102.36mm L x 67.31mm W 高度 - 座高(最大):66.80mm 端接類型:導線引線
ST7-28 制造商:SUPERWORLD 制造商全稱:Superworld Electronics 功能描述:POWER TRANSFORMER
ST7-28B56 功能描述:電源變壓器 SPLIT BOBBIN HORZ MOUNT XFMR RoHS:否 制造商:Triad Magnetics 功率額定值:12 VA 初級電壓額定值:115 V / 230 V 次級電壓額定值:12 V / 24 V 安裝風格:SMD/SMT 一次繞組:Dual Primary Winding 二次繞組:Dual Secondary Winding 長度:2.5 in 寬度:2 in 高度:1.062 in