- 您現在的位置：買賣IC網 > PDF目錄365565 > SII1160 (Silicon Image, Inc.) CASE,HEAVY-DUTY POLY,201407, FOAM FILLED,w/HANDLE,BLACK PDF資料下載
參數資料
| 型號： | SII1160 |
| 廠商： | Silicon Image, Inc. |
| 英文描述： | CASE,HEAVY-DUTY POLY,201407, FOAM FILLED,w/HANDLE,BLACK |
| 中文描述： | PanelLink發射機 |
| 文件頁數： | 29/33頁 |
| 文件大?。?/td> | 494K |
| 代理商： | SII1160 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁
SiI
1160 PanelLink Transmitter
Data Sheet
25
SiI
-DS-0126-B
R
C
Detail of Source termination (magnified)
R and C 0603 components installed.
Figure 18. Source Termination Layout Illustration
The layout in Figure 18 has been developed to minimize trace stubs on the differential TMDS lines, while
providing pads for the source termination components (left-hand magnified view). Source termination components
should be placed close to the transmitter pins. The resistor and capacitor are shown installed on the pads
provided (right-hand magnified view).
Differential Trace Routing
The routing for the
SiI
1160 chip is relatively simple since no spiral skew compensation is needed. However, a few
small precautions are required to achieve the full performance and reliability of
DVI
.
The Transmitter can be placed fairly far from the output connector, but care should be taken to route each
differential signal pair together and achieve impedance of 100
between the differential signal pair. However,
note that the longer the differential traces are between the transmitter and the output connector, the higher the
chance that external signal noise will couple onto the low-voltage signals and affect image quality.
Do not split or have asymmetric trace routing between the differential signal pair. Vias are very inductive and can
cause phase delay problems if applied unevenly within a differential pair. Vias should be minimized or avoided if
possible by placing all differential traces on the top layer of the PCB.
Figure 19 illustrates an incorrect routing of the differential signal from the
SiI
1160 to the DVI connector. Figure 20
illustrates the correct method to route the differential signal from the
SiI
1160 to the DVI connector. Figure 21
illustrates recommended routing for differential traces at the DVI connector.
相關PDF資料 |
PDF描述 |
|---|---|
| SiI1160CTU | PanelLink Transmitter |
| SII1161 | PanelLink Receiver |
| SiI1161CT100 | PanelLink Receiver |
| SiI1161CTU | PanelLink Receiver |
| SII1162 | PanelLink Transmitter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SII1160CTU | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PanelLink Transmitter |
| SII1161 | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PanelLink Receiver |
| SII1161CT100 | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PanelLink Receiver |
| SII1161CTU | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PanelLink Receiver |
| SII1162 | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PanelLink Transmitter |
發布緊急采購，3分鐘左右您將得到回復。