- 您現在的位置：買賣IC網 > PDF目錄365565 > SII1160 (Silicon Image, Inc.) CASE,HEAVY-DUTY POLY,201407, FOAM FILLED,w/HANDLE,BLACK PDF資料下載
參數資料
| 型號： | SII1160 |
| 廠商： | Silicon Image, Inc. |
| 英文描述： | CASE,HEAVY-DUTY POLY,201407, FOAM FILLED,w/HANDLE,BLACK |
| 中文描述： | PanelLink發射機 |
| 文件頁數： | 28/33頁 |
| 文件大?。?/td> | 494K |
| 代理商： | SII1160 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁
SiI
1160 PanelLink Transmitter
Data Sheet
SiI
-DS-0126-B
24
Series Damping Resistors on Outputs
Series resistors are often effective in lowering data-related emissions and reducing reflections. Series resistors
with a value close to the impedance of the board traces are generally most effective in reducing reflections from
the inputs of the transmitter. If used, resistors should be placed close to the output pins of the VGA Source or
Graphics chip, as shown in Figure 16.
DIE[0..23]/
DIO[0..23]
VGA
Figure 16. Series Input Damping Resistors for Driving Source
Source Termination Resistors on Differential Outputs
Source termination, consisting of a 300
resistor and a 0.1
μ
F capacitor, may be used on the differential outputs
of the
SiI
1160 to improve signal swings. See Figure 17 for an illustration. Repeat the circuit for each of the four
differential output pairs: TX0+, TX1+, TX2+, TXC+.
Note that the specific value for the source termination resistor and capacitor will depend on the PCB layout and
construction. Different values may be needed to create optimum DVI-compliant output waveforms from the
transmitter.
300 ohm
0.1uF
TX0+
TX0-
300 ohm
0.1uF
TX1+
TX2-
300 ohm
0.1uF
TX3+
TX3-
300 ohm
0.1uF
TXC+
TXC-
Figure 17. Differential Output Source Terminations
Source termination suppresses signal reflection to prevent non-DVI compliant receivers from erroneously
sampling the TMDS signals at high frequencies (beyond 135MHz). The impact on DVI compliant receivers is
minimal. Therefore Silicon Image recommends source termination for most applications.
Note that the capacitor is required to meet DVI idle mode DC offset requirements and must not be omitted. Note
also that the signal suppression requires the R
EXT_SWING
value to be changed.
Power consumption will be slightly higher when using source termination.
相關PDF資料 |
PDF描述 |
|---|---|
| SiI1160CTU | PanelLink Transmitter |
| SII1161 | PanelLink Receiver |
| SiI1161CT100 | PanelLink Receiver |
| SiI1161CTU | PanelLink Receiver |
| SII1162 | PanelLink Transmitter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SII1160CTU | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PanelLink Transmitter |
| SII1161 | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PanelLink Receiver |
| SII1161CT100 | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PanelLink Receiver |
| SII1161CTU | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PanelLink Receiver |
| SII1162 | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PanelLink Transmitter |
發布緊急采購，3分鐘左右您將得到回復。