- 您現在的位置：買賣IC網 > PDF目錄374746 > sda 9362 (SIEMENS AG) DDC-PLUS-Deflection Controller(DDC 過偏轉控制器) PDF資料下載
參數資料
| 型號： | sda 9362 |
| 廠商： | SIEMENS AG |
| 英文描述： | DDC-PLUS-Deflection Controller(DDC 過偏轉控制器) |
| 中文描述： | DDC的加偏轉控制器（DDC的過偏轉控制器） |
| 文件頁數： | 16/39頁 |
| 文件大?。?/td> | 199K |
| 代理商： | SDA 9362 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
SDA 9362
Semiconductor Group
16
1998-02-01
a) The effective range for
Vertical Blanking Time
:
16 ... 127 (absolute value)
0 ... 127 (offset value)
b) The "default value if disabled" for
Vertical Blanking Time
:
21 (absolute value)
8 (offset value)
c) The effective range for
Start Vertical Scan
:
2 ... 127 (absolute value)
if STE = 0
if STE = 1.
if STE = 0
if STE = 1.
if STE = 0
if STE = 1 and NSA = 1
if STE = 1 and NSA = 0.
-128 ... 127 (offset value)
d) The effective range for
Vertical Scan
(total width: 10 Bit): 160 ... 684 lines.
e) The "default value if disabled" for
Vertical Scan
equals the number of lines of the
source signal reduced by the control value for
Start Vertical Scan
. (E.g.: input signal:
262 lines per field; Start vertical scan = 8 lines; then (if SSE = 1, STE = 0) vertical
scan = 262 - 8 = 254 lines.
At power on the RAM containing the control items is cleared. Therefore all data are zero
by default before transferring individual values via
Ι
2
C Bus.
Allowed values out of the effective range are limited, e. g. Vertical blanking time = 3 is
limited to 16 if STE = 0 (that means a minimum of 16 lines is blanked).
There are five bits (SRSE, BSE, SSE, STE, GBE) in the deflection control byte 1 for
disabling some control items. If one of these bits is "0", the value of the corresponding
control item will be ignored and replaced by the value "default value if disabled" in the
table above.
2.5.4
The
Deflection Control Byte 0
includes the following bits:
Detailed Description
VOFF:
Vertical off
0:
normal vertical output due to control items
1:
vertical saw-tooth is switched off,
vertical protection is disabled
STDBY:
Stand-by mode
0:
normal operation
1:
stand-by mode (all internal clocks are disabled)
VOFF
STDBY
SW2
BD
SW1
VR1
VR0
HDE
相關PDF資料 |
PDF描述 |
|---|---|
| SDA9362 | DDC-PLUS-Deflection Controller |
| sda 9388x | Single-Chip Picture in Picture IC(單芯片畫中畫IC) |
| sda 9400 | Single-Chip Picture in Picture IC(單芯片畫中畫IC) |
| sda 9402 | Single-Chip Picture in Picture IC(單芯片畫中畫IC) |
| sda 9410 | Single-Chip Picture in Picture IC(單芯片畫中畫IC) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SDA9380 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:EDDC MEGAVISION IC set to support single chip back end solutions for SDTV up to HDTV CRTs |
| SDA9380-B21 | 制造商:MICRONAS 制造商全稱:MICRONAS 功能描述:EDDC Enhanced Deflection Controller and RGB Processor |
| SDA9388X | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:Single-Chip Picture in Picture IC |
| SDA9400 | 制造商:MICRONAS 制造商全稱:MICRONAS 功能描述:Scan Rate Converter using Embedded DRAM Technology Units |
| SDA9401 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Scan Rate Converter using Embedded DRAM Technology Units |
發布緊急采購，3分鐘左右您將得到回復。