- 您現在的位置：買賣IC網 > PDF目錄372114 > SAA7146AH (NXP SEMICONDUCTORS) .012UF/400VDC METAL POLY CAP PDF資料下載
參數資料
| 型號： | SAA7146AH |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 消費家電 |
| 英文描述： | .012UF/400VDC METAL POLY CAP |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP160 |
| 封裝： | 28 X 28 MM, 3.40 MM HEIGHT, PLASTIC, SOT322-2, MS-022, QFP-160 |
| 文件頁數： | 142/144頁 |
| 文件大小： | 645K |
| 代理商： | SAA7146AH |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁當前第142頁第143頁第144頁
1998 Apr 09
142
Philips Semiconductors
Product specification
Multimedia bridge, high performance
Scaler and PCI circuit (SPCI)
SAA7146A
13 SOLDERING
13.1
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “IC Package Databook”(order code 9398 652 90011).
13.2
Reflow soldering
Reflow soldering techniques are suitable for all QFP and
SQFP packages.
The choice of heating method may be influenced by larger
plastic QFP packages (44 leads, or more). If infrared or
vapour phase heating is used and the large packages are
not absolutely dry (less than 0.1% moisture content by
weight), vaporization of the small amount of moisture in
them can cause cracking of the plastic body. For more
information, refer to the Drypack chapter in our “Quality
Reference Handbook”(order code 9397 750 00192).
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example,
infrared/convection heating in a conveyor type oven.
Throughput times (preheating, soldering and cooling) vary
between 50 and 300 seconds depending on heating
method. Typical reflow peak temperatures range from
215 to 250
°
C.
13.3
Wave soldering
Wave soldering is
not recommended
for QFP packages
and is
not suitable
for SQFP packages. This is because
of the likelihood of solder bridging due to closely-spaced
leads and the possibility of incomplete solder penetration
in multi-lead devices.
CAUTION
Wave soldering is NOT applicable for all QFP
packages with a pitch (e) equal or less than 0.5 mm.
If wave soldering cannot be avoided, for QFP
packages with a pitch (e) larger than 0.5 mm, the
following conditions must be observed:
A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave)
soldering technique should be used.
The footprint must be at an angle of 45
°
to the board
direction and must incorporate solder thieves
downstream and at the side corners.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Maximum permissible solder temperature is 260
°
C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150
°
C within
6 seconds. Typical dwell time is 4 seconds at 250
°
C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
13.4
Repairing soldered joints
Fix the component by first soldering two diagonally-
opposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300
°
C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
270 and 320
°
C.
相關PDF資料 |
PDF描述 |
|---|---|
| SAA7146A | Multimedia bridge, high performance Scaler and PCI circuit SPCI |
| SAA7151 | Digital multistandard colour decoder with SCART interface DMSD2-SCART |
| SAA7151B | Digital multistandard colour decoder with SCART interface DMSD2-SCART |
| SAA7157 | Clock signal generator circuit for digital TV systems SCGC |
| SAA7157T | Clock signal generator circuit for digital TV systems SCGC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SAA7146AH/V3,557 | 制造商:NXP Semiconductors 功能描述: |
| SAA7146AH/V4,557 | 功能描述:視頻 IC VIDEO PCI BRIDGE (QFP160) RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel |
| SAA7146AH-V4.557 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Multimedia bridge, high performance Scaler and PCI circuit |
| SAA7146AHZ | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Multimedia bridge, high performance Scaler and PCI circuit SPCI |
| SAA7151 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Digital multistandard colour decoder with SCART interface DMSD2-SCART |
發布緊急采購，3分鐘左右您將得到回復。