參數資料
型號： S29GL064M90FCIR83
廠商： Spansion Inc.
英文描述： 256,128,64,32,Megabit 3.0 Volt-only Page Mode Flash Memory featuring 0.23 レm MirrorBit Process Technology
中文描述： 256,128,64,32，3.0兆伏安只頁面模式閃存具有0.23レ米MirrorBit工藝技術
文件頁數： 67/116頁
文件大小： 1656K
代理商： S29GL064M90FCIR83
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBit
TM
Flash Family
65
D a t a S h e e t
Note:
See
Table 34
and
Table 35
for program command sequence
Figure 4. Program Operation
Program Suspend/Program Resume Command Sequence
The Program Suspend command allows the system to interrupt a programming operation or a
Write to Buffer programming operation so that data can be read from any non-suspended sector.
When the Program Suspend command is written during a programming process, the device halts
the program operation within 15 μs maximum (5 μs typical) and updates the status bits. Ad-
dresses are not required when writing the Program Suspend command.
After the programming operation is suspended, the system can read array data from any non-
suspended sector. The Program Suspend command can also be issued during a programming op-
eration while an erase is suspended. In this case, data can be read from any addresses not in
Erase Suspend or Program Suspend. If a read is needed from the Secured Silicon Sector area
(One-time Program area), then user must use the proper command sequences to enter and exit
this region. Note that the Secured Silicon Sector, autoselect, and CFI functions are unavailable
when a program operation is in progress.
The system can also write the autoselect command sequence when the device is in the Program
Suspend mode. The system can read as many autoselect codes as required. When the device
exits the autoselect mode, the device reverts to the Program Suspend mode, and is ready for an-
other valid operation. See
Autoselect Command Sequence
for more information.
After the Program Resume command is written, the device reverts to programming. The system
can determine the status of the program operation using the DQ7 or DQ6 status bits, just as in
the standard program operation. See
Write Operation Status
for more information.
The system must write the Program Resume command (address bits are don’t care) to exit the
Program Suspend mode and continue the programming operation. Further writes of the Resume
command are ignored. Another Program Suspend command can be written after the device re-
sumes programming.
START
Write Program
Command Sequence
Data Poll
from System
Verify Data
No
Yes
Last Address
No
Yes
Programming
Completed
Increment Address
Embedded
Program
algorithm
in progress
相關PDF資料
PDF描述
S29GL064M90TAIR32 256,128,64,32,Megabit 3.0 Volt-only Page Mode Flash Memory featuring 0.23 レm MirrorBit Process Technology
S29GL064M90TAIR33 256,128,64,32,Megabit 3.0 Volt-only Page Mode Flash Memory featuring 0.23 レm MirrorBit Process Technology
S29GL064M90TAIR40 256,128,64,32,Megabit 3.0 Volt-only Page Mode Flash Memory featuring 0.23 レm MirrorBit Process Technology
S29GL064M90TAIR42 256,128,64,32,Megabit 3.0 Volt-only Page Mode Flash Memory featuring 0.23 レm MirrorBit Process Technology
S29GL064M90TAIR43 256,128,64,32,Megabit 3.0 Volt-only Page Mode Flash Memory featuring 0.23 レm MirrorBit Process Technology
相關代理商/技術參數
參數描述
S29GL064M90FFIR2 制造商:Spansion 功能描述:
S29GL064M90TAIR00 制造商:Spansion 功能描述:Flash Mem Parallel 3V/3.3V 64M-Bit 8M x 8 90ns 48-Pin TSOP Tray
S29GL064M90TAIR2 制造商:Spansion 功能描述:
S29GL064M90TAIR20 制造商:Spansion 功能描述:Flash Mem Parallel 3V/3.3V 64M-Bit 8M x 8/4M x 16 90ns 56-Pin TSOP Tray
S29GL064M90TAIR3 制造商:Spansion 功能描述:NOR Flash, 4M x 16, 48 Pin, Plastic, TSSOP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*