參數資料
型號: S1C88104P0A0100
元件分類: 微控制器/微處理器
英文描述: 8-BIT, MROM, 8.2 MHz, MICROCONTROLLER, PBGA240
封裝: VFBGA10H-216
文件頁數: 89/211頁
文件大?。?/td> 1802K
代理商: S1C88104P0A0100
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁當前第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁
S1C8F626 TECHNICAL MANUAL
EPSON
171
APPENDIX A S5U1C88000P1&S5U1C88655P2 MANUAL (Peripheral Circuit Board for S1C8F626)
A.4 Downloading Circuit Data to
the S5U1C88000P1
This board (S5U1C88000P1) comes with the FPGA
that contains factory inspection data, therefore the
circuit data for the model to be used should be
downloaded. The following explains the down-
loading procedure.
1) Set the switch "SW1"1 on this board to the "3"
position.
2) Install this board to the ICE (S5U1C88000H5)
as shown in Section A.2.2.
3) Connect the ICE to the host PC. Then turn the
host PC and ICE on.
4) Invoke the debugger included in the ICE or
assembler package. For how to use the ICE and
debugger, refer to the manuals supplied with
the ICE and assembler package.
5) Download the circuit data file (.mcs) corre-
sponding to the model by entering the follow-
ing commands in the command window.
>XFER
(erase all)
>XFWR
<file name> (download the specified
file)2
>XFCP
<file name> (compare the specified file
and downloaded data)
6) Terminate the debugger and then turn the ICE
off.
7) Remove this board from the ICE and set the
switch "SW1" on the board to the "1" position.
8) Install this board to the ICE again.
9) Turn the ICE on and invoke the debugger
again. Debugging can be started here.
1 See Figure A.1.1, "Board layout", for the
location of SW1.
2 The downloading takes about 5 minutes.
A.5 Precautions
Take the following precautions when using the
S5U1C88000P1&S5U1C88655P2.
A.5.1 Precaution for operation
(1) Turn the power of all equipment off before
connecting or disconnecting cables.
(2) The mask option data must be loaded before
debugging can be started.
A.5.2 Differences from actual IC
Caution is called for due to the following function
and property related differences with the actual
IC. If these precautions are overlooked, it may not
operate on the actual IC, even if it operates on the
ICE in which the S5U1C88000P1&S5U1C88655P2
has been installed.
(1) I/O differences
Interface power voltage
This board and target system interface voltage
is set to +3.3 V. To obtain the same interface
voltage as in the actual IC, attach a level shifter
or similar circuit on the target system side to
accommodate the required interface voltage.
Drive capability of each output port
The drive capability of each output port on this
board is higher than that of the actual IC.
When designing the application system and
software, refer to Chapter 9, "ELECTRICAL
CHARACTERISTICS" to confirm the drive
capability of each output port.
Input port characteristics
The AC characteristic of the input terminal is
different from that of the actual IC and it
affects the input interrupt function. Therefore,
evaluate the operation in the actual IC if the
rise/fall time of the input signal is long.
Protective diode of each port
All I/O ports incorporate a protective diode
for VDD and VSS, and the interface signals
between this board and the target system are
set to +3.3 V. Therefore, this board and the
target system cannot be interfaced with a
voltage exceeding VDD even if the output ports
are configured with open-drain output.
相關PDF資料
PDF描述
S1C88317D0A0100 MICROCONTROLLER, UUC170
S1C88308D0A0100 MICROCONTROLLER, UUC170
S1C88308F0A0100 MICROCONTROLLER, PQFP160
S1C88348F 8-BIT, MROM, 8.2 MHz, MICROCONTROLLER, PQFP16
S1C88316D 8-BIT, MROM, 8.2 MHz, MICROCONTROLLER, UUC172
相關代理商/技術參數
參數描述
S1C88349 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer
S1C88649 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer
S1C88650 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer
S1C88655 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer
S1C88816 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer