參數資料
型號: S1C88104P0A0100
元件分類: 微控制器/微處理器
英文描述: 8-BIT, MROM, 8.2 MHz, MICROCONTROLLER, PBGA240
封裝: VFBGA10H-216
文件頁數: 174/211頁
文件大?。?/td> 1802K
代理商: S1C88104P0A0100
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁當前第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁
S1C8F626 TECHNICAL MANUAL
EPSON
57
5 PERIPHERAL CIRCUITS AND THEIR OPERATION (Serial Interface)
■ Data transmit procedure
The control procedure and operation during
transmitting is as follows.
(1) Write "0" in the transmit enable register TXENx
and the receive enable register RXENx to reset
the serial interface.
(2) Write "1" in the transmit enable register TXENx
to set into the transmitting enable status.
(3) Write the transmitting data into TRXDx0–
TRXDx7.
(4) In case of the master mode, confirm the receive
ready status on the slave side (external serial
input/output device), if necessary. Wait until it
reaches the receive ready status.
(5) Write "1" in the transmit control bit TXTRGx
and start transmitting.
In the master mode, this control causes the
synchronous clock to change to enable and to be
provided to the shift register for transmitting
_________
and output from the SCLKx terminal.
In the slave mode, it waits for the synchronous
_________
clock to be input from the SCLKx terminal.
The transmitting data of the shift register shifts
one bit at a time at each falling edge of the
synchronous clock and is output from the
SOUTx terminal. When the final bit (MSB when
"LSB first" is selected, or LSB when "MSB first"
is selected) is output, the SOUTx terminal is
maintained at that level, until the next transmit-
ting begins.
The transmitting complete interrupt factor flag
FSTRAx is set to "1" at the point where the data
transmitting of the shift register is completed.
When interrupt has been enabled, a transmit-
ting complete interrupt is generated at this
point.
Set the following transmitting data using this
interrupt.
(6) Repeat steps (3) to (5) for the number of bytes of
transmitting data, and then set the transmit
disable status by writing "0" to the transmit
enable register TXENx, when the transmitting is
completed.
Data transmitting
End
TXENx
← 0, RXENx ← 0
No
Yes
Transmit complete ?
Set transmitting data
to TRXDx0–TRXDx7
No
Yes
FSTRAx = 1 ?
TXENx
← 0
TXTRGx
← 1
TXENx
← 1
No
Yes
Receiver ready ?
In case of master mode
Fig. 5.7.6.2 Transmit procedure in clock synchronous mode
相關PDF資料
PDF描述
S1C88317D0A0100 MICROCONTROLLER, UUC170
S1C88308D0A0100 MICROCONTROLLER, UUC170
S1C88308F0A0100 MICROCONTROLLER, PQFP160
S1C88348F 8-BIT, MROM, 8.2 MHz, MICROCONTROLLER, PQFP16
S1C88316D 8-BIT, MROM, 8.2 MHz, MICROCONTROLLER, UUC172
相關代理商/技術參數
參數描述
S1C88349 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer
S1C88649 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer
S1C88650 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer
S1C88655 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer
S1C88816 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer