- 您現在的位置：買賣IC網 > PDF目錄98068 > S1C63653F 4-BIT, FLASH, 4 MHz, MICROCONTROLLER, CQFP100 PDF資料下載
參數資料
| 型號： | S1C63653F |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, FLASH, 4 MHz, MICROCONTROLLER, CQFP100 |
| 封裝： | CERAMIC, QFP15-100 |
| 文件頁數： | 118/121頁 |
| 文件大?。?/td> | 1127K |
| 代理商： | S1C63653F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁當前第118頁第119頁第120頁第121頁
88
EPSON
S1C63653 TECHNICAL MANUAL
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (R/f Converter)
4.12.3 Operation of R/f conversion
Counter
The R/f converter incorporates two types of counters: measurement counter MCxx and time base
counter TCxx. The measurement counter is a 20-bit up counter that counts the CR oscillation clock
with the reference resistance or sensor selected by software. The time base counter is a 20-bit up/
down counter to equal both oscillation times for the reference resistance and the sensor. The time base
counter uses the count clock selected by the RFCLK register (OSC1 or OSC3). Each counter permits
reading and writing on a 4-bit basis.
First start an R/f conversion for the reference resistance. The measurement counter starts counting up
and the time base counter starts counting down. The counters stop counting when the measurement
counter overflows (counter = 00000H). By resetting the time base counter to 00000H before starting an
R/f conversion for the reference resistance, the reference oscillation time will be obtained from the
time base counter.
Then start an R/f conversion for the sensor, the measurement counter starts counting up from 00000H
and the time base counter starts counting up from the counted value. The counters stop counting
when the time base counter overflows (counter = 00000H). The oscillation time in this phase is the
same as that of the reference resistance.
Therefore, by converting a proper initial value for counting of the oscillation of the reference resis-
tance into a complement (value subtracted from 00000H) and setting it into the measurement counter
before starting to count, the number of counts for the sensor oscillation is obtained by reading the
measurement counter after the R/f conversion. In other words, the difference between the reference
resistance and sensor oscillation frequencies can be found easily. For instance, if resistance values of
the reference resistance and the sensor are equivalent, the same value as the initial value before
converting into a complement will be obtained as the result.
The time base counter allows reading of the counter value and presetting of data. By saving the
counter value after the reference oscillation has completed into the RAM, the subsequent reference
oscillation phase can be omitted. The sensor oscillation can be started after setting the saved value to
the time base counter and 00000H to the measurement counter.
Note: When setting the measurement counter, always write 5 words of data continuously in order from
the lower address (FF92H
→ FF93H → FF94H → FF95H → FF96H). Furthermore, an LD instruc-
tion should be used for writing data to the measurement counter and a read-modify-write instruc-
tion (AND, OR, ADD, SUB, etc.) cannot be used.
R/f conversion sequence
An R/f conversion for the reference resistance starts by writing "1" to the register RFRUNR.
However, an initial value must be set to the measurement counter and the time base counter must be
cleared to 00000H before starting the R/f conversion.
When R/f conversion is initiated by the RFRUNR register, oscillation by the reference resistance
begins, and the measurement counter starts counting up from the initial value by the oscillation clock.
The time base counter also starts counting down by the OSC1 clock.
If the measurement counter becomes 00000H due to overflow, the oscillation is terminated. At the
same time an interrupt occurs and the RFRUNR register is set to "0", and the R/f converter circuit
stops operation completely.
The time base counter value should be saved into the RAM for R/f conversion of the sensor.
Figure 4.12.3.1 shows a timing chart for the reference oscillation.
相關PDF資料 |
PDF描述 |
|---|---|
| S1C6F567D0A0100 | MICROCONTROLLER, UUC141 |
| S1C6N3B0D0A0100 | MICROCONTROLLER, UUC54 |
| S1C6P366D0A0100 | 4-BIT, FLASH, 4.1 MHz, MICROCONTROLLER, UUC102 |
| S1C6P466D0A0A00 | MICROCONTROLLER, UUC140 |
| S1C6S2L7D | 4-BIT, MROM, 0.032 MHz, MICROCONTROLLER, UUC58 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1C63656 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63657 | 制造商:EPSON 制造商全稱:EPSON 功能描述:CMOS 4-bit Single Chip Microcontroller |
| S1C63658 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63666 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63709 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
發布緊急采購，3分鐘左右您將得到回復。