- 您現在的位置：買賣IC網 > PDF目錄373330 > RTL8139D(L) RTL8139D(L) Specification PDF資料下載
參數資料
| 型號： | RTL8139D(L) |
| 英文描述： | RTL8139D(L) Specification |
| 中文描述： | RTL8139D（長）規格 |
| 文件頁數： | 6/58頁 |
| 文件大?。?/td> | 616K |
| 代理商： | RTL8139D(L) |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
RTL8100B(L)
2001-11-9
Rev.1.41
6
4. Pin Description
4.1 Power Management/Isolation Interface
Symbol
Type
Pin No
PMEB
(PME#)
ISOLATEB
(ISOLATE#)
Description
O/D
57
Power Management Event:
Open drain, active low. Used by the
RTL8100B(L) to request a change in its current power management
state and/or to indicate that a power management event has occurred.
Isolate Pin:
Active low. Used to isolate the RTL8100B(L) from the PCI
bus. The RTL8100B(L) does not drive its PCI outputs (excluding
PME#) and does not sample its PCI input (including RST# and
PCICLK) as long as the Isolate pin is asserted.
LAN WAKE-UP Signal:
This signal is used to inform the motherboard
to execute the wake-up process. The motherboard must support
Wake-On-LAN (WOL). There are 4 choices of output, including active
high, active low, positive pulse, and negative pulse, that may be asserted
from the LWAKE pin. Please refer to the LWACT bit in the CONFIG1
register and the LWPTN bit in the CONFIG4 register for the setting of
this output signal. The default output is an active high signal.
Once a PME event is received, the LWAKE and PMEB assert at the
same time when the LWPME (bit4, CONFIG4) is set to 0. If the
LWPME is set to 1, the LWAKE asserts only when the PMEB asserts
and the ISOLATEB is low.
This pin is a 3.3V signaling output pin.
I
74
LWAKE
O
64
4.2 PCI Interface
Symbol
AD31-0
Type
T/S
Pin No
Description
86,87,89,91-95,100,
1,3-5,8-10,23-30,33,
36-38,41,42,44,45
98,11,21,32
83
PCI Address and Data Multiplexed Pins
C/BE3-0
CLK
T/S
I
PCI bus command and byte enables multiplexed pins.
Clock:
This PCI Bus clock provides timing for all transactions and bus
phases, and is input to PCI devices. The rising edge defines the start of
each phase. The clock frequency ranges from 0 to 40MHz. For normal
network operation, the RTL8100B(L) requires a minimum PCI clock
frequency of 16.75MHz.
Device Select:
As a bus master, the RTL8100B (L) samples this signal
to insure that a PCI target recognizes the destination address for the data
transfer. As a target, the RTL8100B(L) asserts this signal low when it
recognizes its target address after FRAMEB is asserted.
Cycle Frame:
As a bus master, this pin indicates the beginning and
duration of an access. FRAMEB is asserted low to indicate the start of a
bus transaction. While FRAMEB is asserted, data transfer continues.
When FRAMEB is deasserted, the transaction is in the final data phase.
As a target, the device monitors this signal before decoding the address
to check if the current transaction is addressed to it.
DEVSELB
S/T/S
15
FRAMEB
S/T/S
12
相關PDF資料 |
PDF描述 |
|---|---|
| RTL8150 | RTL8150L(M) Specifications |
| RTL8169 | RTL8169 Specification |
| RTL8201L | Layout guide |
| RTL8204 | Layout reference |
| RTL8305SB | RTL8305SB |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RTL8139D-LF | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SINGLE-CHIP MULTI-FUNCTION 10/100Mbps ETHERNET CONTROLLER WITH POWER MANAGEMENT |
| RTL8139DL-GR | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SINGLE-CHIP MULTI-FUNCTION 10/100Mbps ETHERNET CONTROLLER WITH POWER MANAGEMENT |
| RTL8139DL-LF | 制造商:Realtek Semiconductor 功能描述: |
| RTL8139L | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:REALTEK 3.3V SINGLE CHIP FAST ETHERNET CONTROLLER WITH POWER MANAGEMENT |
| RTL8150 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:RTL8150L(M) Specifications |
發布緊急采購，3分鐘左右您將得到回復。