- 您現在的位置：買賣IC網 > PDF目錄373330 > RTL8139D(L) RTL8139D(L) Specification PDF資料下載
參數資料
| 型號： | RTL8139D(L) |
| 英文描述： | RTL8139D(L) Specification |
| 中文描述： | RTL8139D（長）規格 |
| 文件頁數： | 31/58頁 |
| 文件大?。?/td> | 616K |
| 代理商： | RTL8139D(L) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
RTL8100B(L)
2001-11-9
Rev.1.41
31
5.28 Config5: Configuration Register 5
(Offset 00D8h, R/W)
This register, unlike other Config registers, is not protected by 93C46 Command register. I.e. there is no need to enable Config
register write prior to writing to Config5.
Bit
7
6
R/W
-
R/W
Symbol
-
BWF
Description
Reserved
Broadcast Wakeup Frame:
1: Enable Broadcast Wakeup Frame with mask bytes of only DID
field = FF FF FF FF FF FF.
0: Default value. Disable Broadcast Wakeup Frame with mask bytes
of only DID field = FF FF FF FF FF FF.
The power-on default value of this bit is 0.
Multicast Wakeup Frame:
1: Enable Multicast Wakeup Frame with mask bytes of only DID
field, which is a multicast address.
0: Default value. Disable Multicast Wakeup Frame with mask bytes
of only DID field, which is a multicast address.
The power-on default value of this bit is 0.
Unicast Wakeup Frame:
1: Enable Unicast Wakeup Frame with mask bytes of only DID field,
which is its own physical address.
0: Default value. Disable Unicast Wakeup Frame with mask bytes of
only DID field, which is its own physical address.
The power-on default value of this bit is 0.
FIFO Address Pointer:
(Realtek internal use only to test FIFO SRAM)
1: Both Rx and Tx FIFO address pointers are updated in descending
way from 1FFh and downwards. The initial FIFO address pointer is
1FFh.
0: (Power-on) default value. Both Rx and Tx FIFO address pointers
are updated in ascending way from 0 and upwards. The initial FIFO
address pointer is 0.
Note: This bit does not participate in EEPROM auto-load. The FIFO
address pointers can not be reset, except initial power-on.
The power-on default value of this bit is 0.
Link Down Power Saving mode:
1: Disable.
0: Enable. When cable is disconnected(Link Down), the analog part
will power down itself (PHY Tx part & part of twister) automatically
except PHY Rx part and part of twister to monitor SD signal in case
that cable is re-connected and Link should be established again.
LANWake signal enable/disable:
1: Enable LANWake signal.
0: Disable LANWake signal.
PME_Status bit:
Always sticky/can be reset by PCI RST# and software.
1: The PME_Status bit can be reset by PCI reset or by software.
0: The PME_Status bit can only be reset by software.
5
R/W
MWF
4
R/W
UWF
3
R/W
FIFOAddrPtr
2
R/W
LDPS
1
R/W
LANWake
0
R/W
PME_STS
Config5 register, offset D8h: (SYM_ERR register is changed to Config5, the function of SYM_ERR register is no longer
supported by RTL8100B(L).)
The 3 bits (bit2-0) are auto-loaded from EEPROM Config5 byte to RTL8100B(L) Config5 register.
相關PDF資料 |
PDF描述 |
|---|---|
| RTL8150 | RTL8150L(M) Specifications |
| RTL8169 | RTL8169 Specification |
| RTL8201L | Layout guide |
| RTL8204 | Layout reference |
| RTL8305SB | RTL8305SB |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RTL8139D-LF | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SINGLE-CHIP MULTI-FUNCTION 10/100Mbps ETHERNET CONTROLLER WITH POWER MANAGEMENT |
| RTL8139DL-GR | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SINGLE-CHIP MULTI-FUNCTION 10/100Mbps ETHERNET CONTROLLER WITH POWER MANAGEMENT |
| RTL8139DL-LF | 制造商:Realtek Semiconductor 功能描述: |
| RTL8139L | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:REALTEK 3.3V SINGLE CHIP FAST ETHERNET CONTROLLER WITH POWER MANAGEMENT |
| RTL8150 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:RTL8150L(M) Specifications |
發布緊急采購，3分鐘左右您將得到回復。