- 您現在的位置：買賣IC網 > PDF目錄69306 > R5F212ACSDFP 16-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PQFP48 PDF資料下載
參數資料
| 型號： | R5F212ACSDFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PQFP48 |
| 封裝： | 10 X 10 MM, 0.50 MM PITCH, PLASTIC, LQFP-48 |
| 文件頁數： | 56/138頁 |
| 文件大?。?/td> | 492K |
| 代理商： | R5F212ACSDFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁當前第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁
236
4317K–AVR–03/2013
AT90PWM2/3/2B/3B
21.2
Operation
The ADC converts an analog input voltage to a 10-bit digital value through successive approxi-
mation. The minimum value represents GND and the maximum value represents the voltage on
the AREF pin minus 1 LSB. Optionally, AV
CC or an internal 2.56V reference voltage may be con-
nected to the AREF pin by writing to the REFSn bits in the ADMUX Register. The internal
voltage reference may thus be decoupled by an external capacitor at the AREF pin to improve
noise immunity.
The analog input channel are selected by writing to the MUX bits in ADMUX. Any of the ADC
input pins, as well as GND and a fixed bandgap voltage reference, can be selected as single
ended inputs to the ADC.
The ADC is enabled by setting the ADC Enable bit, ADEN in ADCSRA. Voltage reference is set
by the REFS1 and REFS0 bits in ADMUX register, whatever the ADC is enabled or not. The
ADC does not consume power when ADEN is cleared, so it is recommended to switch off the
ADC before entering power saving sleep modes.
The ADC generates a 10-bit result which is presented in the ADC Data Registers, ADCH and
ADCL. By default, the result is presented right adjusted, but can optionally be presented left
adjusted by setting the ADLAR bit in ADMUX.
If the result is left adjusted and no more than 8-bit precision is required, it is sufficient to read
ADCH. Otherwise, ADCL must be read first, then ADCH, to ensure that the content of the Data
Registers belongs to the same conversion. Once ADCL is read, ADC access to Data Registers
is blocked. This means that if ADCL has been read, and a conversion completed before ADCH
is read, neither register is updated and the result from the conversion is lost. When ADCH is
read, ADC access to the ADCH and ADCL Registers is re-enabled.
The ADC has its own interrupt which can be triggered when a conversion completes. The ADC
access to the Data Registers is prohibited between reading of ADCH and ADCL, the interrupt
will trigger even if the result is lost.
21.3
Starting a Conversion
A single conversion is started by writing a logical one to the ADC Start Conversion bit, ADSC.
This bit stays high as long as the conversion is in progress and will be cleared by hardware
when the conversion is completed. If a different data channel is selected while a conversion is in
progress, the ADC will finish the current conversion before performing the channel change.
Alternatively, a conversion can be triggered automatically by various sources. Auto Triggering is
enabled by setting the ADC Auto Trigger Enable bit, ADATE in ADCSRA. The trigger source is
selected by setting the ADC Trigger Select bits, ADTS in ADCSRB (See description of the ADTS
bits for a list of the trigger sources). When a positive edge occurs on the selected trigger signal,
the ADC prescaler is reset and a conversion is started. This provides a method of starting con-
versions at fixed intervals. If the trigger signal is still set when the conversion completes, a new
conversion will not be started. If another positive edge occurs on the trigger signal during con-
version, the edge will be ignored. Note that an interrupt flag will be set even if the specific
interrupt is disabled or the Global Interrupt Enable bit in SREG is cleared. A conversion can thus
be triggered without causing an interrupt. However, the interrupt flag must be cleared in order to
trigger a new conversion at the next interrupt event.
相關PDF資料 |
PDF描述 |
|---|---|
| R5F212BCSNFP | 16-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PQFP48 |
| R5F212BASNFP | 16-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PQFP48 |
| R5F212ACSNFP | 16-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PQFP48 |
| R5F212BASNLG | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PBGA64 |
| R5F212BCSNLG | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PBGA64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| R5F212ACSDFP#U0 | 制造商:Renesas Electronics Corporation 功能描述:IC MCU 16BIT R8C2A 64LQFP |
| R5F212ACSDFP#V2 | 制造商:Renesas Electronics Corporation 功能描述:R8C/2A 128+0/7.5 64LQFP 10X10 -40 TO +85 - Trays 制造商:Renesas Electronics Corporation 功能描述:IC MCU 16BIT 128KB FLASH 64LQFP |
| R5F212ACSDXXXFA | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:RENESAS MCU R8C FAMILY / R8C/2x SERIES |
| R5F212ACSDXXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:RENESAS MCU R8C FAMILY / R8C/2x SERIES |
| R5F212ACSNFA | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:MCU |
發布緊急采購，3分鐘左右您將得到回復。