參數資料
型號： R5F212ACSDFP
元件分類： 微控制器/微處理器
英文描述： 16-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PQFP48
封裝： 10 X 10 MM, 0.50 MM PITCH, PLASTIC, LQFP-48
文件頁數： 17/138頁
文件大?。?/td> 492K
代理商： R5F212ACSDFP
200
4317K–AVR–03/2013
AT90PWM2/3/2B/3B
figure), to decide if a valid start bit is received. If two or more of these three samples have logical
high levels (the majority wins), the start bit is rejected as a noise spike and the Receiver starts
looking for the next high to low-transition. If however, a valid start bit is detected, the clock recov-
ery logic is synchronized and the data recovery can begin. The synchronization process is
repeated for each start bit.
18.8.2
Asynchronous Data Recovery
When the receiver clock is synchronized to the start bit, the data recovery can begin. The data
recovery unit uses a state machine that has 16 states for each bit in Normal mode and eight
states for each bit in Double Speed mode. Figure 18-7 shows the sampling of the data bits and
the parity bit. Each of the samples is given a number that is equal to the state of the recovery
unit.
Figure 18-7. Sampling of Data and Parity Bit
The decision of the logic level of the received bit is taken by doing a majority voting of the logic
value to the three samples in the center of the received bit. The center samples are emphasized
on the figure by having the sample number inside boxes. The majority voting process is done as
follows: If two or all three samples have high levels, the received bit is registered to be a logic 1.
If two or all three samples have low levels, the received bit is registered to be a logic 0. This
majority voting process acts as a low pass filter for the incoming signal on the RxD pin. The
recovery process is then repeated until a complete frame is received. Including the first stop bit.
Note that the Receiver only uses the first stop bit of a frame.
Figure 18-8 shows the sampling of the stop bit and the earliest possible beginning of the start bit
of the next frame.
Figure 18-8. Stop Bit Sampling and Next Start Bit Sampling
The same majority voting is done to the stop bit as done for the other bits in the frame. If the stop
bit is registered to have a logic 0 value, the Frame Error (FE) flag will be set.
A new high to low transition indicating the start bit of a new frame can come right after the last of
the bits used for majority voting. For Normal Speed mode, the first low level sample can be at
point marked (A) in Figure 18-8. For Double Speed mode the first low level must be delayed to
(B). (C) marks a stop bit of full length. The early start bit detection influences the operational
range of the Receiver.
12
34
56
7
8
9
10
11
12
13
14
15
16
1
BIT x
123
4
5
678
1
RxDn
Sample
(U2Xn = 0)
Sample
(U2Xn = 1)
12
34
56
7
8
9
10
0/1
STOP 1
123
4
5
6
0/1
RxDn
Sample
(U2Xn = 0)
Sample
(U2Xn = 1)
(A)
(B)
(C)
相關PDF資料
PDF描述
R5F212BCSNFP 16-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PQFP48
R5F212BASNFP 16-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PQFP48
R5F212ACSNFP 16-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PQFP48
R5F212BASNLG 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PBGA64
R5F212BCSNLG 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PBGA64
相關代理商/技術參數
參數描述
R5F212ACSDFP#U0 制造商:Renesas Electronics Corporation 功能描述:IC MCU 16BIT R8C2A 64LQFP
R5F212ACSDFP#V2 制造商:Renesas Electronics Corporation 功能描述:R8C/2A 128+0/7.5 64LQFP 10X10 -40 TO +85 - Trays 制造商:Renesas Electronics Corporation 功能描述:IC MCU 16BIT 128KB FLASH 64LQFP
R5F212ACSDXXXFA 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:RENESAS MCU R8C FAMILY / R8C/2x SERIES
R5F212ACSDXXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:RENESAS MCU R8C FAMILY / R8C/2x SERIES
R5F212ACSNFA 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:MCU
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*