參數資料
型號： R5F21274JFP
元件分類： 微控制器/微處理器
英文描述： 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP32
封裝： 7 X 7 MM, 0.80 MM PITCH, PLASTIC, LQFP-32
文件頁數： 43/52頁
文件大小： 620K
代理商： R5F21274JFP
65
ATmega165A/PA/325A/PA/3250A/PA/645A/P/6450A/P [DATASHEET]
8285E–AVR–02/2013
Note:
1. For the assembly program, two temporary registers are used to minimize the time from pull-ups are set on pins 0,
1, 6, and 7, until the direction bits are correctly set, defining bit 2 and 3 as low and redefining bits 0 and 1 as strong
high drivers.
14.2.5
Digital Input Enable and Sleep modes
As shown in Figure 14-2, the digital input signal can be clamped to ground at the input of the Schmidt Trigger. The
signal denoted SLEEP in the figure, is set by the MCU Sleep Controller in Power-down mode, Power-save mode,
and Standby mode to avoid high power consumption if some input signals are left floating, or have an analog signal
level close to V
CC/2.
SLEEP is overridden for port pins enabled as external interrupt pins. If the external interrupt request is not enabled,
SLEEP is active also for these pins. SLEEP is also overridden by various other alternate functions as described in
If a logic high level (“one”) is present on an asynchronous external interrupt pin configured as “Interrupt on Rising
Edge, Falling Edge, or Any Logic Change on Pin” while the external interrupt is not enabled, the corresponding
External Interrupt Flag will be set when resuming from the above mentioned Sleep mode, as the clamping in these
sleep mode produces the requested logic change.
14.2.6
Unconnected pins
If some pins are unused, it is recommended to ensure that these pins have a defined level. Even though most of
the digital inputs are disabled in the deep sleep modes as described above, floating inputs should be avoided to
reduce current consumption in all other modes where the digital inputs are enabled (Reset, Active mode and Idle
mode).
The simplest method to ensure a defined level of an unused pin, is to enable the internal pull-up. In this case, the
pull-up will be disabled during reset. If low power consumption during reset is important, it is recommended to use
an external pull-up or pull-down. Connecting unused pins directly to V
CC or GND is not recommended, since this
may cause excessive currents if the pin is accidentally configured as an output.
14.3
Alternate port functions
Most port pins have alternate functions in addition to being general digital I/Os. Figure 14-5 on page 66 shows how
the port pin control signals from the simplified Figure 14-2 on page 62 can be overridden by alternate functions.
The overriding signals may not be present in all port pins, but the figure serves as a generic description applicable
to all port pins in the AVR microcontroller family.
相關PDF資料
PDF描述
R5F21264SNXXXFP 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP32
R5F21265SNXXXFP 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP32
R5F21272SNFP 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP32
R5F21264KXXXFP 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP32
R5F21264JFP 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP32
相關代理商/技術參數
參數描述
R5F21274JFP#U0 功能描述:MCU FLASH 2K FLASH 16K 32LQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:R8C/2x/27 標準包裝:250 系列:80C 核心處理器:8051 芯體尺寸:8-位 速度:16MHz 連通性:EBI/EMI，I²C，UART/USART 外圍設備:POR，PWM，WDT 輸入/輸出數:40 程序存儲器容量:- 程序存儲器類型:ROMless EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-LCC（J 形引線） 包裝:帶卷 (TR)
R5F21274JFP#W4 制造商:Renesas Electronics Corporation 功能描述:MCU 3/5V - Tape and Reel
R5F21274JXXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MCU
R5F21274KFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:RENESAS 16-BIT SINGLE-CHIP MCU R8C FAMILY / R8C/2x SERIES
R5F21274KXXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MCU
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*