參數資料
型號: R5F21274JFP
元件分類: 微控制器/微處理器
英文描述: 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP32
封裝: 7 X 7 MM, 0.80 MM PITCH, PLASTIC, LQFP-32
文件頁數: 32/52頁
文件大?。?/td> 620K
代理商: R5F21274JFP
55
ATmega165A/PA/325A/PA/3250A/PA/645A/P/6450A/P [DATASHEET]
8285E–AVR–02/2013
When the BOOTRST Fuse is programmed and the Boot section size set to 4Kbytes, the most typical and general
program setup for the Reset and Interrupt Vector Addresses is:
Address
Labels Code
Comments
.org 0x0002
0x0002
jmp
EXT_INT0
; IRQ0 Handler
0x0004
jmp
PCINT0
; PCINT0 Handler
...
;
0x002C
jmp
SPM_RDY
; Store Program Memory Ready Handler
;
.org 0x3800/0x7800
0x3800/0x7801RESET:ldir16,high(RAMEND); Main program start
0x3801/0x7801
out
SPH,r16
; Set Stack Pointer to top of RAM
0x3802/0x7802
ldi
r16,low(RAMEND)
0x3803/0x7803
out
SPL,r16
0x3804/0x7804
sei
; Enable interrupts
0x3805/0x7805
<instr>
xxx
When the BOOTRST Fuse is programmed, the Boot section size set to 4Kbytes and the IVSEL bit in the MCUCR
Register is set before any interrupts are enabled, the most typical and general program setup for the Reset and
Interrupt Vector Addresses is:
Address
Labels Code
Comments
;
.org 0x3800/0x7800
0x3800/0x7800
jmp
RESET
; Reset handler
0x3802/0x7802
jmp
EXT_INT0
; IRQ0 Handler
0x3804/0x7804
jmp
PCINT0
; PCINT0 Handler
...
;
0x382C/0x782C
jmp
SPM_RDY
; Store Program Memory Ready Handler
;
0x382E/0x782ERESET:ldir16,high(RAMEND); Main program start
0x382F/0x782F
out
SPH,r16
; Set Stack Pointer to top of RAM
0x3830/0x7830
ldi
r16,low(RAMEND)
0x3831/0x7831
out
SPL,r16
0x3832/0x7832
sei
; Enable interrupts
0x3833/0x7833
<instr>
xxx
12.2
Moving interrupts between application and Boot Space
The General Interrupt Control Register controls the placement of the Interrupt Vector table, see ”MCUCR – MCU
To avoid unintentional changes of Interrupt Vector tables, a special write procedure must be followed to change the
IVSEL bit:
a.
Write the Interrupt Vector Change Enable (IVCE) bit to one.
b.
Within four cycles, write the desired value to IVSEL while writing a zero to IVCE.
Interrupts will automatically be disabled while this sequence is executed. Interrupts are disabled in the cycle IVCE
is set, and they remain disabled until after the instruction following the write to IVSEL. If IVSEL is not written, inter-
rupts remain disabled for four cycles. The I-bit in the Status Register is unaffected by the automatic disabling.
Note:
If Interrupt Vectors are placed in the Boot Loader section and Boot Lock bit BLB02 is programmed, interrupts are dis-
abled while executing from the Application section. If Interrupt Vectors are placed in the Application section and Boot
Lock bit BLB12 is programed, interrupts are disabled while executing from the Boot Loader section. Refer to the sec-
相關PDF資料
PDF描述
R5F21264SNXXXFP 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP32
R5F21265SNXXXFP 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP32
R5F21272SNFP 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP32
R5F21264KXXXFP 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP32
R5F21264JFP 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP32
相關代理商/技術參數
參數描述
R5F21274JFP#U0 功能描述:MCU FLASH 2K FLASH 16K 32LQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:R8C/2x/27 標準包裝:250 系列:80C 核心處理器:8051 芯體尺寸:8-位 速度:16MHz 連通性:EBI/EMI,I²C,UART/USART 外圍設備:POR,PWM,WDT 輸入/輸出數:40 程序存儲器容量:- 程序存儲器類型:ROMless EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-LCC(J 形引線) 包裝:帶卷 (TR)
R5F21274JFP#W4 制造商:Renesas Electronics Corporation 功能描述:MCU 3/5V - Tape and Reel
R5F21274JXXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MCU
R5F21274KFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:RENESAS 16-BIT SINGLE-CHIP MCU R8C FAMILY / R8C/2x SERIES
R5F21274KXXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MCU