- 您現在的位置：買賣IC網 > PDF目錄69305 > R5F21274JFP 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP32 PDF資料下載
參數資料
| 型號： | R5F21274JFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP32 |
| 封裝： | 7 X 7 MM, 0.80 MM PITCH, PLASTIC, LQFP-32 |
| 文件頁數： | 36/52頁 |
| 文件大?。?/td> | 620K |
| 代理商： | R5F21274JFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁當前第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
59
ATmega165A/PA/325A/PA/3250A/PA/645A/P/6450A/P [DATASHEET]
8285E–AVR–02/2013
Bit 5 – PCIE1: Pin Change Interrupt Enable 1
When the PCIE1 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), pin change interrupt 1 is
enabled. Any change on any enabled PCINT15...8 pin will cause an interrupt. The corresponding interrupt of Pin
Change Interrupt Request is executed from the PCI1 Interrupt Vector. PCINT15:8 pins are enabled individually by
the PCMSK1 Register.
Bit 4 – PCIE0: Pin Change Interrupt Enable 0
When the PCIE0 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), pin change interrupt 0 is
enabled. Any change on any enabled PCINT7...0 pin will cause an interrupt. The corresponding interrupt of Pin
Change Interrupt Request is executed from the PCI0 Interrupt Vector. PCINT7:0 pins are enabled individually by
the PCMSK0 Register.
Bit 0 – INT0: External Interrupt Request 0 Enable
When the INT0 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), the external pin interrupt is
enabled. The Interrupt Sense Control0 bits 1/0 (ISC01 and ISC00) in the External Interrupt Control Register A
(EICRA) define whether the external interrupt is activated on rising and/or falling edge of the INT0 pin or level
sensed. Activity on the pin will cause an interrupt request even if INT0 is configured as an output. The correspond-
ing interrupt of External Interrupt Request 0 is executed from the INT0 Interrupt Vector.
13.2.3
EIFR – External Interrupt Flag Register
Bit 7 – PCIF3: Pin Change Interrupt Flag 3
When a logic change on any PCINT30:24 pin triggers an interrupt request, PCIF3 becomes set (one). If the I-bit in
SREG and the PCIE3 bit in EIMSK are set (one), the MCU will jump to the corresponding Interrupt Vector. The flag
is cleared when the interrupt routine is executed. Alternatively, the flag can be cleared by writing a logical one to it.
Note:
1. This bit is a reserved bit in Atmel
ATmega165A/ATmega165PA/ATmega325A/ATmega325PA/ATmega645A/ATmega645P and should always be writ-
ten to zero.
Bit 6 – PCIF2: Pin Change Interrupt Flag 2
When a logic change on any PCINT24:16 pin triggers an interrupt request, PCIF2 becomes set (one). If the I-bit in
SREG and the PCIE2 bit in EIMSK are set (one), the MCU will jump to the corresponding Interrupt Vector. The flag
is cleared when the interrupt routine is executed. Alternatively, the flag can be cleared by writing a logical one to it.
Note:
1. This bit is a reserved bit in Atmel
ATmega165A/ATmega165PA/ATmega325A/ATmega325PA/ATmega645A/ATmega645P and should always be writ-
ten to zero.
Bit 5 – PCIF1: Pin Change Interrupt Flag 1
When a logic change on any PCINT15:8 pin triggers an interrupt request, PCIF1 becomes set (one). If the I-bit in
SREG and the PCIE1 bit in EIMSK are set (one), the MCU will jump to the corresponding Interrupt Vector. The flag
is cleared when the interrupt routine is executed. Alternatively, the flag can be cleared by writing a logical one to it.
Bit 4 – PCIF0: Pin Change Interrupt Flag 0
When a logic change on any PCINT7:0 pin triggers an interrupt request, PCIF0 becomes set (one). If the I-bit in
SREG and the PCIE0 bit in EIMSK are set (one), the MCU will jump to the corresponding Interrupt Vector. The flag
is cleared when the interrupt routine is executed. Alternatively, the flag can be cleared by writing a logical one to it.
Bit
76543210
0x1C (0x3C)
PCIF3
PCIF2
PCIF1
PCIF0
–
INTF0
EIFR
Read/Write
R/W
RRR
R/W
Initial Value
00000000
相關PDF資料 |
PDF描述 |
|---|---|
| R5F21264SNXXXFP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP32 |
| R5F21265SNXXXFP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP32 |
| R5F21272SNFP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP32 |
| R5F21264KXXXFP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP32 |
| R5F21264JFP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| R5F21274JFP#U0 | 功能描述:MCU FLASH 2K FLASH 16K 32LQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:R8C/2x/27 標準包裝:250 系列:80C 核心處理器:8051 芯體尺寸:8-位 速度:16MHz 連通性:EBI/EMI，I²C，UART/USART 外圍設備:POR，PWM，WDT 輸入/輸出數:40 程序存儲器容量:- 程序存儲器類型:ROMless EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-LCC（J 形引線） 包裝:帶卷 (TR) |
| R5F21274JFP#W4 | 制造商:Renesas Electronics Corporation 功能描述:MCU 3/5V - Tape and Reel |
| R5F21274JXXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MCU |
| R5F21274KFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:RENESAS 16-BIT SINGLE-CHIP MCU R8C FAMILY / R8C/2x SERIES |
| R5F21274KXXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MCU |
發布緊急采購，3分鐘左右您將得到回復。