- 您現在的位置：買賣IC網 > PDF目錄368020 > PI7C7100 (Pericom Semiconductor Corp.) 3-Port PCI Bridge PDF資料下載
參數資料
| 型號： | PI7C7100 |
| 廠商： | Pericom Semiconductor Corp. |
| 英文描述： | 3-Port PCI Bridge |
| 中文描述： | 3端口PCI橋 |
| 文件頁數： | 80/132頁 |
| 文件大?。?/td> | 2559K |
| 代理商： | PI7C7100 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁當前第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁
72
09/18/00 Rev 1.1
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456
15. IEEE 1149.1 Compatible JTAG Controller
PI7C7100
3-Port PCI Bridge
ADVANCE INFORMATION
An IEEE 1149.1 compatible Test Access Port (TAP) controller and associated TAP pins are provided to support boundary
scan in PI7C7100 for board-level continuity test and diagnostics. The TAP pins assigned are TCK, TDI, TDO, TMS and
TRST#. All digital input, output, input/output pins are tested except TAP pins and clock pin.
The IEEE 1149.1 Test Logic consists of a TAP controller, an instruction register, and a group of test data registers including
Bypass, Device Identification and Boundary Scan registers. The TAP controller is a synchronous 16 state machine driven
by the Test Clock (TCK) and the Test Mode Select (TMS) pins. An independent power on reset circuit is provided to ensure
the machine is in TEST_LOGIC_RESET state at power-up. The JTAG signal lines are not active when the PCI resource
is operating PCI bus cycles.
PI7C7100 implements 3 basic instructions: BYPASS, SAMPLE/PRELOAD, EXTEST.
15.1 Boundary Scan Architecture
Boundary-scan test logic consists of a boundary-scan register and support logic. These are accessed through a Test
Access Port (TAP). The TAP provides a simple serial interface that allows all processor signal pins to be driven and/or
sampled, thereby providing direct control and monitoring of processor pins at the system level.
This mode of operation is valuable for design debugging and fault diagnosis since it permits examination of connections
not normally accessible to the test system. The following subsections describe the boundary-scan test logic elements:
TAP pins, instruction register, test data registers and TAP controller. Figure 15-1 illustrates how these pieces fit together
to form the JTAG unit.
15.1.1 TAP Pins
The PI7C7100’s TAP pins form a serial port composed of four input connections (TMS, TCK, TRST# and TDI) and one output
connection (TDO). These pins are described in Table 15-1. The TAP pins provide access to the instruction register and
the test data registers.
15.1.2 Instruction Register
The Instruction Register (IR) holds instruction codes. These codes are shifted in through the Test Data Input (TDI) pin. The
instruction codes are used to select the specific test operation to be performed and the test data register to be accessed.
The instruction register is a parallel-loadable, master/slave-configured 2-bit wide, serial-shift register with latched outputs.
Data is shifted into and out of the IR serially through the TDI pin clocked by the rising edge of TCK. The shifted-in instruction
becomes active upon latching from the master stage to the slave stage. At that time the IR outputs along with the TAP
finite state machine outputs are decoded to select and control the test data register selected by that instruction. Upon
latching, all actions caused by any previous instructions terminate.
Boundary-Scan Register
Control and Clock Signals
TAP
Controller
Instruction
Register
Bypass Register
TDO
TDI
TMS
TCK
TRST#
TAP Pins
PI7C7100 System Pins
Figure 15-1. Test Access Port Block Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| PI7C7100CNA | 3-Port PCI Bridge |
| PI7C7300 | 3-PORT PCI-to-PCI BRIDGE |
| PI7C7300A | 3-PORT PCI-to-PCI BRIDGE |
| PI7C7300ANA | 3-PORT PCI-to-PCI BRIDGE |
| PI7C8140A | 2 PORT PCI TO PCI BRIDGE PLX PCI 6140 COMPARISON |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PI7C7100BNA | 制造商:Pericom Semiconductor Corporation 功能描述:3 PORT PCI TO PCI |
| PI7C7100CNA | 制造商:PERICOM 制造商全稱:Pericom Semiconductor Corporation 功能描述:3-Port PCI Bridge |
| PI7C7300 | 制造商:PERICOM 制造商全稱:Pericom Semiconductor Corporation 功能描述:3-PORT PCI-to-PCI BRIDGE |
| PI7C7300A | 制造商:PERICOM 制造商全稱:Pericom Semiconductor Corporation 功能描述:3-PORT PCI-to-PCI BRIDGE |
| PI7C7300AEVB-3 | 功能描述:界面開發工具 3 Port PCI Bridge Eval Brd RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
發布緊急采購，3分鐘左右您將得到回復。