參數資料
型號： PCA9541
廠商： NXP Semiconductors N.V.
英文描述： 2-to-1 I2C master selector with interrupt logic and reset
中文描述： 2比1的I2C主機選擇與中斷邏輯和復位
文件頁數： 5/30頁
文件大?。?/td> 279K
代理商： PCA9541
Philips Semiconductors
Product data sheet
PCA9541
2-to-1 I
2
C master selector with interrupt logic and reset
2004 Oct 01
5
DEVICE ADDRESS
Following a START condition, the upstream master that wants to
control the I
2
C-bus or make a status check must send the address
of the slave it is accessing. The slave address of the PCA9541 is
shown in Figure 4. To conserve power, no internal pull-up resistors
are incorporated on the hardware selectable pins and they must be
pulled HIGH or LOW.
A1 A0
1
1
A3 A2
SW02011
1
R/W
FIXED
HARDWARE
SELECTABLE
Figure 4. Slave address
The last bit of the slave address defines the operation to be
performed. When set to logic 1 a read is selected while logic 0
selects a write operation.
COMMAND CODE
Following the successful acknowledgement of the slave address,
the bus master will send a byte to the PCA9541, which will be stored
in the Command Code register.
0
SW02302
0
B1
0
0
AI
0
REGISTER
NUMBER
B0
AUTO
INCREMENT
Figure 5. Command Code
The 2 LSBS are used as a pointer to determine which register will
be accessed.
If the auto-increment flag is set (AI=1), the two least significant bits
of the Command Code are automatically incremented after a byte
has been read or written. This allows the user to program the
registers sequentially or to read them sequentially.
–
During a Read operation, the contents of these bits will rollover
to “00” after the last allowed register is accessed (“10”).
–
During a Write operation, the PCA9541 will acknowledge bytes
sent to the IE and CONTROL registers but will not acknowledge
a byte sent to the Interrupt Status Register since it is a
read-only register. The 2 LSB’s of the Command Code do not
roll over to 00 but stays at 10.
Only the 2 least significant bits are affected by the AI flag.
Unused bits must be programmed with zeroes. Any command code
(Write operation) different from “000AI0000”, “000AI0001”, and
“000AI0010” will not be acknowledged. At power-up, this register
defaults to all zeros.
Table 1.
Command Code Register
B1
B0
REGISTER
NAME
TYPE
REGISTER
FUNCTION
0
0
IE
Read/Write
Interrupt
Enable
0
1
CONTROL
Read/Write
Control Switch
1
0
ISTAT
Read
Interrupt
Status
1
1
NOT ALLOWED
Each system master controls its own set of registers, however they
can also read specific bits from the other system master.
PCA9541 INTERNAL REGISTER MAP
IE
CONTROL
ISTAT
IE
CONTROL
ISTAT
REG#00
REG#01
REG#10
REG#00
REG#01
REG#10
IE 0
CONTROL 0
ISTAT 0
MASTER 0
SCL_MST0
SDA_MST0
MASTER 1
SCL_MST1
SDA_MST1
SW02072
IE 1
CONTROL 1
ISTAT 1
PCA9541
0
1
2
3
4
5
6
7
CONTROL REGISTER DETAIL
CONTROL 0
CONTROL 1
Figure 6. Internal register map
相關PDF資料
PDF描述
PCA9542 2-channel IIC multiplexer and interrupt controller(2通道IIC多路復用器和中斷控制器)
PCA9542PW 2-channel I2C multiplexer and interrupt controller
PCA9542PWDH 2-channel I2C multiplexer and interrupt controller
PCA9543 2-channel I2C switch with interrupt logic and reset
PCA9543D 2-channel I2C switch with interrupt logic and reset
相關代理商/技術參數
參數描述
PCA9541_08 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:2-to-1 I2C-bus master selector with interrupt logic and reset
PCA9541_09 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:2-to-1 I2C-bus master selector with interrupt logic and reset
PCA9541A 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:2-to-1 I2C-bus master selector with interrupt logic and reset
PCA9541ABS/01 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:2-to-1 I2C-bus master selector with interrupt logic and reset
PCA9541ABS/01,118 功能描述:I2C 接口集成電路 2-to-1 I2C-bus master selector RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*