- 您現在的位置：買賣IC網 > PDF目錄367809 > PCA9541 (NXP Semiconductors N.V.) 2-to-1 I2C master selector with interrupt logic and reset PDF資料下載
參數資料
| 型號： | PCA9541 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 2-to-1 I2C master selector with interrupt logic and reset |
| 中文描述： | 2比1的I2C主機選擇與中斷邏輯和復位 |
| 文件頁數： | 15/30頁 |
| 文件大?。?/td> | 279K |
| 代理商： | PCA9541 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
Philips Semiconductors
Product data sheet
PCA9541
2-to-1 I
2
C master selector with interrupt logic and reset
2004 Oct 01
15
Acknowledge
The number of data bytes transferred between the start and the stop conditions from transmitter to receiver is not limited. Each byte of eight bits
is followed by one acknowledge bit. The acknowledge bit is a HIGH level put on the bus by the transmitter whereas the master generates an
extra acknowledge related clock pulse.
A slave receiver which is addressed must generate an acknowledge after the reception of each byte. Also a master must generate an
acknowledge after the reception of each byte that has been clocked out of the slave transmitter. The device that acknowledges has to pull down
the SDA line during the acknowledge clock pulse, so that the SDA line is stable LOW during the HIGH period of the acknowledge related clock
pulse, set-up and hold times must be taken into account.
A master receiver must signal an end of data to the transmitter by not generating an acknowledge on the last byte that has been clocked out of
the slave. In this event, the transmitter must leave the data line HIGH to enable the master to generate a stop condition.
DATA OUTPUT
BY TRANSMITTER
SCL FROM
MASTER
SW00368
DATA OUTPUT
BY RECEIVER
1
2
8
9
S
START condition
clock pulse for
acknowledgement
acknowledge
not acknowledge
Figure 11. Acknowledgement on the I
2
C-bus
相關PDF資料 |
PDF描述 |
|---|---|
| PCA9542 | 2-channel IIC multiplexer and interrupt controller(2通道IIC多路復用器和中斷控制器) |
| PCA9542PW | 2-channel I2C multiplexer and interrupt controller |
| PCA9542PWDH | 2-channel I2C multiplexer and interrupt controller |
| PCA9543 | 2-channel I2C switch with interrupt logic and reset |
| PCA9543D | 2-channel I2C switch with interrupt logic and reset |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA9541_08 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:2-to-1 I2C-bus master selector with interrupt logic and reset |
| PCA9541_09 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:2-to-1 I2C-bus master selector with interrupt logic and reset |
| PCA9541A | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:2-to-1 I2C-bus master selector with interrupt logic and reset |
| PCA9541ABS/01 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:2-to-1 I2C-bus master selector with interrupt logic and reset |
| PCA9541ABS/01,118 | 功能描述:I2C 接口集成電路 2-to-1 I2C-bus master selector RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
發布緊急采購，3分鐘左右您將得到回復。